| Author |
Message |
 Topic: Ramsey 50 winch parts? |
Bill_F
Replies: 13
Views: 14138
|
 Forum: Wanted Posted: Thu Jan 16, 2020 6:00 pm Subject: Ramsey 50 winch parts? |
Do you have a hood number and serial number for that jeep? We are trying to track winch jeeps.
Ryan if you are looking for mine it is not an orginal winch jeep. |
| Topic: Ramsey 50 winch parts? |
Bill_F
Replies: 13
Views: 14138
|
Forum: Wanted Posted: Fri Jan 10, 2020 2:03 pm Subject: Ramsey 50 winch parts? |
| I sent the guy that did mine the case, the lever, and the shaft. It all worked out well. |
| Topic: Ramsey 50 winch parts? |
Bill_F
Replies: 13
Views: 14138
|
Forum: Wanted Posted: Wed Jan 08, 2020 12:50 pm Subject: Ramsey 50 winch parts? |
| No I just sent him the part and he made the new one. |
| Topic: Ramsey 50 winch parts? |
Bill_F
Replies: 13
Views: 14138
|
Forum: Wanted Posted: Thu Jan 02, 2020 11:12 am Subject: Ramsey 50 winch parts? |
| Mine was in really tough shape and I had someone machine a new one. |
| Topic: Engine has problem keeping coils alive |
Bill_F
Replies: 6
Views: 7439
|
Forum: Technical Knowledge Base Posted: Wed Jul 10, 2019 8:51 pm Subject: Engine has problem keeping coils alive |
| Took out the protronix kit. Been running points and have had no coil issues. Now I can a little bit of a put out of the exhaust but I have not finished tuning yet. |
| Topic: Electrical Issue- NO SPARK - Need help! |
Bill_F
Replies: 16
Views: 15760
|
Forum: Technical Knowledge Base Posted: Sat Jun 15, 2019 3:17 am Subject: Re: no Spark |
What is the part number for the Napa condenser. I need a 24 volt one for my 1955 38a1
The condensor doesnt care the voltage. Go to your local parts store and ask for one for a cj3a. It is the same ... |
| Topic: Engine has problem keeping coils alive |
Bill_F
Replies: 6
Views: 7439
|
Forum: Technical Knowledge Base Posted: Tue Jun 04, 2019 4:53 pm Subject: Engine has problem keeping coils alive |
I have replaced all the wire in the distributor, it is in good shape. I am not using an orginal ignition switch, I put a keyed switch in .
I am leaning to something with the pertronix, it has give ... |
| Topic: Engine has problem keeping coils alive |
Bill_F
Replies: 6
Views: 7439
|
Forum: Technical Knowledge Base Posted: Tue Jun 04, 2019 1:10 pm Subject: Engine has problem keeping coils alive |
| Also to note jeep was running great last night, took it about 5 miles, at about mile 4 it start to cough and loose power, about 300 yards from my house I had to put it in low range to get it home. Op ... |
| Topic: Engine has problem keeping coils alive |
Bill_F
Replies: 6
Views: 7439
|
Forum: Technical Knowledge Base Posted: Tue Jun 04, 2019 1:08 pm Subject: Engine has problem keeping coils alive |
1) Pretronix is wired correctly and has been working well for years
2) All vacuum lines are hooked up as they are supposed to be
Did get the jeep to fire again last night after I found it had spar ... |
| Topic: Ramsey 50 or 50R winch, pto and more |
Bill_F
Replies: 5
Views: 8781
|
Forum: Wanted Posted: Fri Apr 26, 2019 12:43 pm Subject: Ramsey 50 or 50R winch, pto and more |
| It took me awhile to find all the parts to my winch setup. It started with the winch itself which was attached to a cj5, they I found a pto on craigslist, then another that came with the hanger beari ... |
| Topic: Ramsey 50 or 50R winch, pto and more |
Bill_F
Replies: 5
Views: 8781
|
Forum: Wanted Posted: Fri Apr 26, 2019 12:31 pm Subject: Ramsey 50 or 50R winch, pto and more |
Good luck on finding a Gardwood level wind. I have never seen a jeep one for sale, and only seen photos of it, on one jeep.
As for the rest of the parts they do come up for sale every so often. ... |
| Topic: Bell crank and rebuild parts |
Bill_F
Replies: 17
Views: 16291
|
Forum: Wanted Posted: Sun Dec 23, 2018 11:20 am Subject: Bell crank and rebuild parts |
| Wes any time you can use better bearings the life will increase. I used a nos kit when I redid my jeep years ago. It only took about 5000 miles for it to weare out. I bet the new system lasts much lon ... |
| Topic: Bell crank and rebuild parts |
Bill_F
Replies: 17
Views: 16291
|
Forum: Wanted Posted: Sun Dec 23, 2018 10:58 am Subject: Bell crank and rebuild parts |
| I redid my bell crank with tapered roller bearings. A guy on the cj5 page is doing the machine work. Best upgrade ever. Took out all the slop and will last much longer. |
| Topic: 1953 M38A1 Front Seat Springs wanted...FOUND |
Bill_F
Replies: 6
Views: 8524
|
Forum: Wanted Posted: Thu Dec 20, 2018 7:32 am Subject: 1953 M38A1 Front Seat Springs wanted...FOUND |
| I have extra seat spring for the front. |
| Topic: PTO Question |
Bill_F
Replies: 5
Views: 6721
|
Forum: Technical Knowledge Base Posted: Sat Dec 15, 2018 6:29 am Subject: PTO Question |
| Wes if you find a complete Ramsey 50 setup for 2500 please forward it to me. The last Ramsey 105a pto I sold alone 5 years ago went for $1000. The hanger bearing is $700 for a repop, I have not seen a ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
