Author |
Message |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Wed Jan 06, 2010 3:25 pm Subject: engine block serial numbers |
Wes,
After a long delay, I am finally getting back to the Jeep. I have cleaned the area that you suggested above the water pump and it is clean with no numbers of any kind. I used a fihe wire br ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Thu Oct 08, 2009 11:14 pm Subject: Pictures Posted |
Wes,
I looked for the serial numbers on the "flat" area that you indicated with your techical drawing. The spot is clean. See pics in gallery for details. Is there any other place to look for the ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Thu Oct 08, 2009 4:05 pm Subject: It Turns over |
Once I installed the newly rebuilt starter and hooked up the battery, the engine turns over and is waiting to start. Phase one is complete. Now onto Phase two. Thanks for everones help to get the proj ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Thu Oct 08, 2009 10:40 am Subject: You have the engine number |
Wes,
I didn't realize that the engine photo provides the engine number. Thanks for the info. My question now is why would a person install a later alternator/starter combination on an older engin ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Thu Oct 08, 2009 10:32 am Subject: Delco starter numbers |
Wes,
I could not find any numbers on the starter. Now that it has been rebuilt, it is all clean and painted and without any evidence of numbers. I will report back in about an hour to let you kno ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Wed Oct 07, 2009 11:23 pm Subject: Photos posted in gallery under BULSI |
I have successfully posted the photos in the Gallery under bulsi (page 7)
Since the last post, I have picked up the rebuilt starter. I plan to install it on Thursday. I will post results Thursday nig ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Wed Oct 07, 2009 12:02 pm Subject: Photo Album Issue |
Wes,
I took your advise and went to the photo album. I don't see any information on how I can set up my own photo album. Do I need an ID from Gallery or what is the correct procedure?
Thanks, ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Tue Oct 06, 2009 12:28 pm Subject: Pictures added |
I have added some pictures to more clearly show what I am dealing with. The starter has been sent out for rebuild. Hopefully, I will have everything back together by the weekend.
Wally
[img]http:/ ... |
Topic: Will an M38A1 or CJ3 body work on an M38 chassis |
bulsi
Replies: 4
Views: 8631
|
Forum: Technical Knowledge Base Posted: Mon Oct 05, 2009 11:05 pm Subject: 1960,61 Falcon Carburater |
Wes, I have done some research on using a Falcon carb to resolve my height issue on the M38 hood with the F134 engine. Can you tell me the following:
Holley or Carter Carb
4cyl engine or 6 cyl eng ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Fri Oct 02, 2009 11:56 pm Subject: Unable to post pictures |
I have taken pictures of the starter gear and ring gear. I didn't realize that I can't upload from my computer without going through a public domain. After reviewing your iinformation, I am going to e ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Wed Sep 30, 2009 8:33 am Subject: Starting Problem with OHV jeep engine |
I have not attempted to start the engine yet. I am only attempting to get the engine to turn over. When I hold the starter button down, I can get the engine to turn a quarter turn before the bendix ki ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Mon Sep 28, 2009 9:53 pm Subject: Starting Problem with OHV jeep engine |
The battery is new and fully charged. The ground is tight. I have not attempted the gas down the carb yet. The points are not pitted. The plugs are clean. The coil is getting 12 volts when I turn the ... |
Topic: Starting Problem with OHV jeep engine |
bulsi
Replies: 23
Views: 27174
|
Forum: Technical Knowledge Base Posted: Sun Sep 27, 2009 10:28 pm Subject: Starting Problem with OHV jeep engine |
I am attempting to start an OHV 4 cylinder jeep engine which has a Delco alternator and a Delco starter which I believe was used by Jeep between 1966 and 1971. I finally figured out the primary wiring ... |
Topic: Will an M38A1 or CJ3 body work on an M38 chassis |
bulsi
Replies: 4
Views: 8631
|
Forum: Technical Knowledge Base Posted: Sun Sep 27, 2009 10:10 pm Subject: Will an M38A1 or CJ3 body work on an M38 chassis |
Wes,
Thanks for the input. I will stick with the M38 body. I do have a starting problem that I will address with a new question. I will also attempt to get the engine number so it will be easier ... |
Topic: Will an M38A1 or CJ3 body work on an M38 chassis |
bulsi
Replies: 4
Views: 8631
|
Forum: Technical Knowledge Base Posted: Sat Sep 26, 2009 8:50 pm Subject: Will an M38A1 or CJ3 body work on an M38 chassis |
.I have a 1951 M38 Jeep with a later OHV Jeep engine. It also has a snow plow welded to the front. The engine runs and the drivetrain appears to look like it will perform ok. The body is shot as well ... |
|