| Author |
Message |
 Topic: M38Cdn Carb Dilemma |
wesk
Replies: 9
Views: 436
|
 Forum: Technical Knowledge Base Posted: Thu May 08, 2025 8:40 pm Subject: M38Cdn Carb Dilemma |
The last kit I bought from Midwest:
http://willysmjeeps.com/v2/modules/gallery/albums/album83/Midwest_kit_labeled.sized.jpg
For the full size view: http://willysmjeeps.com/v2/modules/gallery/al ... |
| Topic: M38Cdn Carb Dilemma |
wesk
Replies: 9
Views: 436
|
Forum: Technical Knowledge Base Posted: Wed May 07, 2025 12:47 pm Subject: M38Cdn Carb Dilemma |
Good that you are reading. All the answers are in those manuals and if you conform to the specs then problems usually go away.
As for rod lengths they wear, come from different manufacturers and ev ... |
| Topic: M38 frame serial number tag? |
wesk
Replies: 5
Views: 324
|
Forum: Technical Knowledge Base Posted: Mon May 05, 2025 10:05 pm Subject: M38 frame serial number tag? |
| Thanks Kendall. That was a dumb typo!! |
| Topic: M38 frame serial number tag? |
wesk
Replies: 5
Views: 324
|
Forum: Technical Knowledge Base Posted: Mon May 05, 2025 8:35 pm Subject: M38 frame serial number tag? |
Did the M38 have a small tag on the front frame horn
NO
Could he have a MB frame under his M38 body?
Yes
machine gun mount cross member on his frame...did the MB's all have them?
Yes &am ... |
| Topic: M38Cdn Carb Dilemma |
wesk
Replies: 9
Views: 436
|
Forum: Technical Knowledge Base Posted: Sun May 04, 2025 1:47 pm Subject: M38Cdn Carb Dilemma |
| The fuel pump pressure range is in the M38 Operator's Handbook TM 9-8012 or the old version TM 9-804. |
| Topic: M38Cdn Carb Dilemma |
wesk
Replies: 9
Views: 436
|
Forum: Technical Knowledge Base Posted: Sun May 04, 2025 12:22 am Subject: M38Cdn Carb Dilemma |
| Pete, You did not mention what manual you are using for your carb work. The Army did publish TM 9-1826A dtd 12/1952 Ordnance Maintenance Carter Carbs. This is the only manual I know of specific to the ... |
| Topic: Exhaust gases been drawn into Jeep. M38a1 |
wesk
Replies: 4
Views: 635
|
Forum: Technical Knowledge Base Posted: Wed Apr 30, 2025 11:12 am Subject: Exhaust gases been drawn into Jeep. M38a1 |
| Fairly common with any open jeep. Gets worse if the engine is running to rich or burning oil. Remember when the US Army asked for an off road open bodied military transport in 1940 they never planned ... |
| Topic: pvc |
wesk
Replies: 4
Views: 1214
|
Forum: Technical Knowledge Base Posted: Thu Apr 24, 2025 11:05 am Subject: pvc |
Hello Jean and welcome to our web site. Just so we are all on the same subject, Jean is from Belgium. He is working on his CJ3B also known as a M606.
So your 3B has been converted to an electric f ... |
| Topic: Photo gallery request |
wesk
Replies: 3
Views: 668
|
Forum: Photo Posting & Gallery requests/problems Posted: Mon Mar 31, 2025 7:46 pm Subject: Photo gallery request |
Pleasenote the main board discussion on the closing of the Photo album access.
http://www.willysmjeeps.com/v2/modules.php?name=Forums&file=viewtopic&t=13785&start=15 |
| Topic: M38a1 rear transfer case yoke bolts |
wesk
Replies: 2
Views: 2889
|
Forum: Wanted Posted: Thu Mar 27, 2025 8:20 pm Subject: M38a1 rear transfer case yoke bolts |
Are you referring to item CC in your ORD 9 SNL G-758 page 197, Fig 08-3?
http://willysmjeeps.com/v2/modules/gallery/albums/album167/08_3_Xfer.sized.jpg
It is a set screw Steel, 3/8x24NF x 0.72 ( ... |
| Topic: T-90 gear condition w/photos |
wesk
Replies: 2
Views: 2949
|
Forum: Technical Knowledge Base Posted: Mon Mar 24, 2025 12:13 am Subject: T-90 gear condition w/photos |
| Since they are pitted with corrosion which has penetrated their hardened surface there is always the risk of crack development at the weakened areas that can quickly lead to fractures. Still, it is yo ... |
| Topic: M38 top starter bolt |
wesk
Replies: 7
Views: 4751
|
Forum: Technical Knowledge Base Posted: Sun Mar 16, 2025 10:51 pm Subject: M38 top starter bolt |
| The lower front support bracket should be the last bolt you remove. |
| Topic: M38 top starter bolt |
wesk
Replies: 7
Views: 4751
|
Forum: Technical Knowledge Base Posted: Sun Mar 16, 2025 8:34 pm Subject: M38 top starter bolt |
| I think you are over thinking this starter removal. If one is patient one simply needs to leave the bottom starter bolt tight and loosen the top bolt with an open end wrench. Two or three turns loose ... |
| Topic: M38 top starter bolt |
wesk
Replies: 7
Views: 4751
|
Forum: Technical Knowledge Base Posted: Sun Mar 16, 2025 11:49 am Subject: M38 top starter bolt |
| https://www.zoro.com/static/cms/product/large/Z1F20_fo5oy.JPG |
| Topic: Bumper numbers M38 |
wesk
Replies: 2
Views: 3898
|
Forum: Technical Knowledge Base Posted: Mon Mar 10, 2025 7:47 pm Subject: Bumper numbers M38 |
| The quickest way is to google for an on line club for the Unit you wish the jeep to represent. Then review their historical photos and find a photo taken during the time period you want your jeep to r ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
