Joined: Jan 09, 2009 Posts: 34 Location: Newnan, Georgia
Posted: Mon Jul 20, 2009 6:45 am Post subject: Crossmember replacement
I bought a MWM M38 crossmember for my M606 frame, I removed my old crossmember and cleaned up the frame horns. The replacement crossmember is drilled 1/2 holes and the frame is 3/8 holes, I was wondering how you'all completed installation with the mismatched holes. After fitting it most holes are good as far as matching the frame holes, but did you weld up the holes and back drill the new holes or enlarge the frame holes to 1/2?
_________________ '53 CJ3B Hurricane, 5.38s, lockrights, koenig PTO winch. M606 conversion in progress.
In the land of the blind.... the one eyed man is king
Joined: Nov 02, 2007 Posts: 437 Location: Seguin, Texas
Posted: Mon Jul 20, 2009 7:00 am Post subject:
My only experience has been with an m38a-1.....but it appears as if my rear crossmember was riveted on with rivets with big flat heads.......maybe the hole size difference is by design. Just my $.02 worth.
This discrepency has been addressed in the past and has been explained as a manufacturer's deliberate attempt to make the crossmember easier to fit with many frames that may not be in perfect alignment. This is a nice idea but I personally would like to see a more accurate repop show up on the market. If this was truly necessary then all repop frame parts would have the wrong size holes. In the ineterim if you want the perfect fit either weld the new holes shut and backdrill or weld in small plugs and backdrill. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
I beg to differ. The holes in the crossmember were measured from an original M38A1 part. The hole diameter is not supposed to be the same size. They compensated for the expansion of the rivet to take care of this. It was not an arbitrary decision on our part to make one that "caters" to multiple vehicles. We have recently dissected an 1952 M38 and the hole on that crossmember match the one we made. If you all want a crossmember with smaller holes, just say so and we will make it otherwise. Won't be correct, but what ever you guys want, we will make.
John
Joined: Jan 09, 2009 Posts: 34 Location: Newnan, Georgia
Posted: Wed Jul 22, 2009 11:43 am Post subject:
Can I send mine back in exchange for one drilled 3/8" That would make it sooo much easier? _________________ '53 CJ3B Hurricane, 5.38s, lockrights, koenig PTO winch. M606 conversion in progress.
In the land of the blind.... the one eyed man is king
Joined: Nov 02, 2007 Posts: 437 Location: Seguin, Texas
Posted: Wed Jul 22, 2009 12:15 pm Post subject:
I'm guessing it must take some kind of a metallurgic or mechanical engineering degree to fully understand why some things are done the way they are done......why some things are welded....and some things are riveted......and other things have a combination of both......and some things just get bolted together. I can "see" this issue from both sides......from the need to fit old, mishapened frames......to being over-sized because they have always been over-sized and thus will continue to be reproduced that way.......what it really comes down to......is just how "accurate" YOU want YOUR restoration to be. Personally.....I'd settle for 3/8" nuts and bolts with over-sized flat washers over the 1/2" holes......but I know this would probably bring shivers down some people's spines. but then.......all I'm after is functionality. Soooo....to thine own self be true........or like Uncle Charlie used to say.....machts du vas du wilst.......which loosely translated means.......do whatever you want to do because that's what you want to do anyway. hehehe......
Joined: Jan 09, 2009 Posts: 34 Location: Newnan, Georgia
Posted: Wed Jul 22, 2009 3:13 pm Post subject:
I'm not biulding a numbers matching restow by any means, but may have stumble upon a cheap answer- 7/16" flat head mild steel rivets for $5.45 for 1lb of rivets. Can be cold worked with a BFH
Shot the rivets with the help of a friends torch and a rivet gun with a flush set and a heavy bucking bar (one of the perks of aircraft maint). I used the rivets included with the crossmember, I didn't think they were the right size for the hole size drilled in the crossmember- but they turned out fine- see what you think! Crossmember treated with a rust conversion coating (Must for Rust from Home Depot) so it looks galvanized but it isn't.
Thanks Midwest military for a quality product!
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
Posted: Thu Jul 30, 2009 7:29 pm Post subject:
That looks great. I wish you had some pictures of the tools so I could rig up something.
To summarize your procedure, you heated the rivets to red, put the bucking bar against the revet head on outside of bumper and flattened out the rivet with the rivet gun. How did you reach in those tight areas to flatten them out?
And one final question, what is a flush set?
I was just planning on using some regular bolts but I was going to turn down the bolt head so my Marine bumper will fit over.
I am an aircraft mechanic and use these tools very often. In fact a lot over the past 45 years. We seldom used more than a 3X gun and rarely have to heat or use steel rivets. Howver when you start talking 3/8" steel rivets and 5X or 6X gun and a torch you must heat these rivets cherry red to set them adequately. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: Jan 09, 2009 Posts: 34 Location: Newnan, Georgia
Posted: Fri Jul 31, 2009 7:00 am Post subject:
I used this bar for the upper and lower rivets. For the rear facing rivets I used a flat bar clamped to hold the rivet head against the frame and shot the tail of the rivet with the flush set, could have been done the other way.
http://www.aircraft-tool.com/shop/detail.aspx?PRODUCT_ID=141
hit the pawn shops in your area and I bet a air chisel would work good also. _________________ '53 CJ3B Hurricane, 5.38s, lockrights, koenig PTO winch. M606 conversion in progress.
In the land of the blind.... the one eyed man is king
I own several long and short barrel air chisels. Their stroke is way too long. Makes them impossible to control and keep within a 1" circle. With two hands and a lot of determination you can occasional make the short barrel stand still but if you are spending money for a used tool you may as well buy the right one for the job.
Most larger cities also have used tool resale shops. If you are close to any large aircraft manufacturing town like Riverside, Wichita, Ft. Worth, Macon, and Seatle then you can get real lucky since they have resale tool stores for their tooling used in finished aircraft contracts. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
Posted: Fri Jul 31, 2009 9:25 am Post subject:
Excellent! Thanks for the info, procedures and description of what tools I need for the job. I have a pretty well equipped home machine shop but there is always something new to learn and a new tool to add.
First, I will call around to the tool rental shops and see if they have this tool.
An extra set of hands is always a good idea. Especially with the large bore 4X and bigger rivet guns. It can be quite difficult to kepp the flush rivet set where you want it and work the bucking bar on the other side of the rivet by yourself. If that rivet gun walks, you will get some serious deep sharp dents on the adjacent steel. We call the assistant the "Buckee".
Note: This type work can be tough on old farts like me. You get something akin to tennis elbow from the hammering effect on your arm. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
