Joined: Jun 09, 2011 Posts: 776 Location: Bellmore, NY
Posted: Tue Jun 19, 2012 9:57 pm Post subject: No overdrive love?
My overdrive is stuck in permanently on. I thought, if you shift forward, you hit neutral. Further forward, you hit overdrive. I have it all the way back, but I can cruise easily at 60 miles an hour, so the overdrive must be engaged. I could never do that before. I have tried pushing it forward, which is neutral, and it's fine there. I push it even further forward, and it stays there until I let up the clutch, at which point it pops back into neutral. Does anyone know anything about overdrives, and have some advice? _________________ 1952 M38A1
Marine core reinforced rear bumper, military transistorized turn signal upgrade, arctic heater, 11" drum brakes, 200L PTO winch, Huffy overdrive, deep water fording kit, RT 68 vehicle mounted radio, Trac Locs front and rear.
www.danhenk.com
The answer Herm gave you in the your first post on this topic is still the answer you need to followup on.
Quote:
Deadguy
Member
Joined: Jun 09, 2011
Posts: 362
Location: Philadelphia, PA
Posted: Thu Jun 14, 2012 3:39 am Post subject:
I talked to "Herm the overdrive guy" today. He says it is most likely a sticking synchro. The overdrive/rebuilt engine/transmission/transfer case setup doesn't have that many miles on it. He says it may loosen up and wear in in time, or I might need to pull it and have it gone through.
_________________
1952 M38A1
Words have no meaning
When they are said by shallow minds.
www.danhenk.com
Joined: Jun 09, 2011 Posts: 776 Location: Bellmore, NY
Posted: Tue Jun 19, 2012 10:12 pm Post subject:
I talked to herm again today, and he seemed very unsure. He was going to call Novak and call me back. I'm not that familiar with overdrives, but it is definitely engaged, but the shift lever seems to indicate it's in direct. _________________ 1952 M38A1
Marine core reinforced rear bumper, military transistorized turn signal upgrade, arctic heater, 11" drum brakes, 200L PTO winch, Huffy overdrive, deep water fording kit, RT 68 vehicle mounted radio, Trac Locs front and rear.
www.danhenk.com
What synchro is he referring to here? The tranny 2nd/3rd synchro can blow out completely and have no effect on the Overdrive shifting. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: Jun 09, 2011 Posts: 776 Location: Bellmore, NY
Posted: Tue Jun 19, 2012 10:58 pm Post subject:
Like I said, I have no experience with overdrives. I would guess he is talking about the internals of the overdrive unit, but I have no idea. _________________ 1952 M38A1
Marine core reinforced rear bumper, military transistorized turn signal upgrade, arctic heater, 11" drum brakes, 200L PTO winch, Huffy overdrive, deep water fording kit, RT 68 vehicle mounted radio, Trac Locs front and rear.
www.danhenk.com
Joined: Mar 28, 2008 Posts: 353 Location: BrOoKlYn
Posted: Wed Jun 20, 2012 8:54 am Post subject:
Does the OD shift stalk have ample engaging clearance from your dash to allow full forward travel?
One would require to bend stalk aft (for certain appl.) to allow clearance.
I had to do this with an unmodified M170 set up. _________________ Always Looking for M170 Parts and bits
Joined: Jun 09, 2011 Posts: 776 Location: Bellmore, NY
Posted: Wed Jun 20, 2012 12:07 pm Post subject:
i don't know, I can check. When I push it all the way forward, it is right up against the dash. One big concern, though, is doesn't pushing it forward engage the overdrive? Mine is already engaged. It's all the way back. Middle is neutral, and forward is what it pops out of _________________ 1952 M38A1
Marine core reinforced rear bumper, military transistorized turn signal upgrade, arctic heater, 11" drum brakes, 200L PTO winch, Huffy overdrive, deep water fording kit, RT 68 vehicle mounted radio, Trac Locs front and rear.
www.danhenk.com
Joined: Mar 28, 2008 Posts: 353 Location: BrOoKlYn
Posted: Wed Jun 20, 2012 12:24 pm Post subject:
Yes that is correct, forward is overdrive.
Did you install the unit and linkage or your mechanic?
Talk to Herm. I suggest you send him pics of your linkage install with shift rail positions in relation to your stalk position. I'm not qualified to speculate any further. _________________ Always Looking for M170 Parts and bits
I think it depends on if the plunger on the OD unit is in front or in the rear, that makes the difference if you push forward to engage it or pull backward to engage it. _________________ Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum