Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
Posted: Thu Jan 22, 2015 10:17 pm Post subject:
Thank you Sir!
Yes, all cold worked. I was sweating bullets as I got the bend
near 90 degrees, but went slow and took my time. The real scary
moments were when I had to bring the ends back to square
from twisting while making the big bends.
They aren't perfect but only you, Rick and Wes would notice!
You can do them without heat. And the second one is easier
as you can start in the middle and work your way to the ends
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
Posted: Tue Jan 27, 2015 2:09 pm Post subject: sheet metal work
Started on the hood. Money and a fear of minimum metal left to work with has made the decision not to media blast. I am paying the price in sweat equity instead. This also gives me an appreciation for the guys in the past that did all of this stuff by hand.
The hood was a mess. Several coats of paint and Bondo. Fording and slave cable cutout badly patched with bubblegum welds and a gallon of Bondo. I borrowed a MIG, Youngest son says he can weld 18 gauge sheet. I'll save that repair until he comes out next.
In the meantime, began removing the junk on top. Heated up with a propane torch, then paint scraper. Mostly paint scraper. Then sand paper. Got it down to mostly metal. Pulled the hood and laid it flat upside down on the garage floor and began working on the dents. Sanded again then hit it with some etching primer to protect the metal.
Went to the driver's side then decided I needed to take at least one photo.
I started with the torch, but gave up and went to the scraper.
I have no idea what those two holes were for. One match on the other side.
Unfortunately there is no green paint under Bubba's first couple of coats of primer and Bondo, so I gave up on any chance at hood numbers.
Here's one for the Strata Blue guys. The left fender was worse than the hood. It had been mashed, stood on, and pounded out so much the fender had pulled out of the inner fenderwell, and the horizontal sheetmetal was so stretched there was no way to bring it back to true. I first thought the support had bent, but a square on it underneath showed it to be good. The fender only had spot welds out at the very end holding it. Everything else was popped. Once I figured that out I realized the dented section where it attached to the support was at the correct place, everything else was stretched something awful in the vertical. So. I drilled 1/8" holes through the fender and bracket moving in towards the fender well, two at a time, and putting Clecos in. Then drill the next pair of holes, and so on.
Once I got near the fenderwell, I kneeled on top of the fender and that pushed the fender back down where it belonged in relation to the fenderwell. Drilled and Clecoed fore and aft to where that edge was again semi-square. Then I went back and removed the Clecos one at a time and replaced with screws and locknuts to hold the mess. Once #2 son shows up I'll pull the screws one at a time and have him spot weld.
These are neat little gizmos and come in a variety of hole diameters. They were designed for riveting airplanes together. You drill the holes, put the panels together, Cleco them up, then rivet. I bought these years ago for a train project which I have yet to use them on, so this was my first go. It won't be the last.
As you can see from the last photo this old girl will never be a trailer queen with things like that fender. I didn't buy her to be one, but I'll fix her up and make her as presentable as possible with my means, and drive.
One day if I win the lottery maybe I'll buy a new hood and fenders. As Wes said in another post, all I have to do is paint them and bolt them on. That's the way Willys did it, and I'm sure the motor pool guys as well.
Joined: Jul 24, 2014 Posts: 80 Location: Fort Bliss Texas
Posted: Wed Jan 28, 2015 5:23 pm Post subject:
I'm digging through a pile of junk that the mechanics have dubbed trash ... that's where I found my perfect condition tail light. I need a black out light but if I find 2 I could send the other to you if you need one. I still need the mounting "hoop" for the fender black out drive lamp but I'm sure I can get my hands on at least one of em for my fender from our wasteful mechanics. Pretty cool that the 113s use the same BO (looks the same anyway) and tail lights that the M38 did
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
Posted: Thu Jan 29, 2015 9:15 am Post subject:
Grab as much wiring, cables, and harnesses as you can especially if they have connectors. The wire is useable if in good condition, and the wire number identifiers are handy as well!
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
Posted: Thu Jan 29, 2015 9:23 am Post subject:
I have worked my way around the hood, skipping the right side that needs to be cut out and replaced, straightening, sanding, and priming. Made it to the cowl, then the dash. Two days with a paint scraper and sandpaper and I am here:
I have a lot of work ahead, but I'm tackling what is right in front, or more importantly, like saving old buildings, starting on the top and working my way down.
Wes, there is a hole maybe 3/8 or a little bigger, on the lower left side of the dash, in line with the priming pump hole where the start button currently is. Unfortunately it is obscured by the steering wheel.
There are also two other holes on the right side. One just to the bottom left of the right bracket mount for the windshield attachment. One more to the right and near the top right corner of the dash.
Any idea what any of these holes would have been for? Also, how were the door straps and/or seat belts retrofitted if at all?
Slowly and surely it is all starting to become the same color, even if primer.
It is a shame you didn't purchase Ryan's M38 resto guide book. Early and late dashes are well illustrated on page 143.
At the far lower left edge of the dash (slightly lower than the primer pump) is the hole for the garwood winch control used on some of the pre-production prototypes. The Garwood winch was not used during production but the hole was left there.
On the right there are only three holes above the glove box. Two for the windshield hold down bracket and one for the glove box door striker. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
Posted: Thu Jan 29, 2015 12:36 pm Post subject:
It's out there, Wes, and can be had. Maybe my birthday or Christmas
wish list.
Well the winch hole makes sense. I'll plug it with a tap in.
The other two, well I guess Bubba struck again. Maybe needed
a spot to hang a drink holder.....
The bigger hole? Not sure. It's right at the lower left corner
of the windshield mount screw hole.
It has rust in the usual places, in the bottom where the wrapped up piece holds the hinge pins on. But, doesn't appear to be as bad as it could be. What I can see into the pin areas looks pretty good.
It has plenty of warts, and will need some work, but for a driver and maybe eventual motor pool, I believe it beats a repop.
Interesting paint. On the interior side, it looks like red lead over steel, and black paint over the primer.
The back is red lead over steel, then what looks like faded zinc chromate, then a bad green. Some of it appears almost a light olive, and a brighter green, then of course the black, then more yellow.
I can't find anything that looks like 2430 anywhere.
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
Posted: Sun Feb 15, 2015 12:56 pm Post subject:
As the fox says,"Some days chicken, some days feathers."
As bought my hammer had a gas can bracket bolted to the left rear quarter and valance panel. Don't ask..........
So I was cleaning up the tailgate, removing snaps, drilling out plugs and broken screws and bolts where there should be holes, grinding off what was left of the gas can strap bracket. You know, the usual things.
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
Posted: Mon Mar 16, 2015 3:54 pm Post subject:
Stopped at a junk shop today that always seemed to be closed.
He had 5 G cans for 25 a piece. I'd bite if I didn't have one already.
On the shelf below was this weird, misshapen thing like a hollow
shoe on one end and a slot running down the thing. A 5/16 piece of
rod with rubber on it and a couple of metal pieces obviously held
something in place. Asked the guy if he would take 15 for it but he insisted
on 25. Then he asked me if I knew what it was.
I told him it was a rifle rack for a jeep.
Now I need to get my windshield back here from Georgia so I have
something to bolt it to
Joined: Aug 31, 2010 Posts: 1744 Location: SO IDAHO
Posted: Wed Mar 18, 2015 11:15 am Post subject:
Nice score on the rack Brian! Is the spring and cam in the barrel holddown still functional, ie does it cam over to a stop perpendicular to the rack? _________________ keep 'em rollin'
RICKG MC 51986 DOD 01-52, '50 CJ3a
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
