View previous topic :: View next topic |
Author |
Message |
Jake266 Member
Joined: Sep 09, 2010 Posts: 51 Location: Missouri
|
Posted: Sat Nov 04, 2017 6:35 am Post subject: WTB neoprene washer for AB15 No Longer Needed |
|
|
Looking for a neoprene washer for the AB15 antenna if anyone has one available.
DISREGARD. Made one out of a tire patch.
Last edited by Jake266 on Tue Nov 07, 2017 2:11 pm; edited 2 times in total |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3452 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
Posted: Sat Nov 04, 2017 9:12 am Post subject: |
|
|
His post about the washer issue on the tech board has all the infor.
Quote: |
Site Administrator
Site Administrator
Joined: Apr 04, 2005
Posts: 12945
Location: Wisconsin
PostPosted: Fri Oct 27, 2017 12:16 pm Post subject: Reply with quote Edit/Delete this post Delete this post View IP address of poster
Detail C in this drawing doesn't show any washers between AB-15 and MP-50.
View larger version: http://willysmjeeps.com/v2/modules/gallery/albums/album227/SC_D_28605.jpg
That only means the AB15 when installed on the MP50 doesn't require any separate washers on the radio set instructions. The washers you are concerned with may only show up on a detailed parts list or drawing for the AB15 specifically. You need a copy of the Parts List for the AB-15/GR antenna base. TM 11-5985-230-14P.
http://www.liberatedmanuals.com/TM-11-5985-230-14P.pdf
GASKET NO-REF-DESIG 3 X 1-29-32 X 1-16 IN. Ref Drwg SCD12520-2 (80063) NSN 5310-00-189-8907 PN SA212 (Entron Industries Lp) or PN HP8009 (Henry Products). Specs below:
Quote:
5310-00-189-8907, 5310001898907 Characteristics Data
MRC Criteria Characteristic
AAGR CROSS-SECTIONAL SHAPE STYLE RECTANGULAR
AAUB HOLE DIAMETER 1.906 INCHES NOMINAL
ABMW PERIPHERAL SHAPE STYLE ROUND
ABMX CENTER HOLE SHAPE STYLE ROUND
ABNM THICKNESS 0.062 INCHES NOMINAL
ADAV OVERALL DIAMETER 3.000 INCHES NOMINAL
CQBC III MINIMUM TENSILE STRENGTH 1 POUNDS PER SQUARE INCH
CQFM HARDNESS RATING 35.0 DUROMETER MINIMUM AND 45.0 DUROMETER MAXIMUM
MATT MATERIAL RUBBER SYNTHETIC OVERALL
MDCL MATERIAL DOCUMENT AND CLASSIFICATION MIL-R-3065 MIL SPEC SINGLE MATERIAL RESPONSE OVERALL
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Last edited by wesk on Fri Oct 27, 2017 2:30 pm; edited 1 time in total |
_________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3452 Location: Texas Hill Country
|
|
Back to top |
|
|
Jake266 Member
Joined: Sep 09, 2010 Posts: 51 Location: Missouri
|
Posted: Mon Nov 06, 2017 6:52 am Post subject: |
|
|
Brian,
Didn't know about the sheets. I'll be driving by a TS today so I'll stop in and see if they have it. Thanks. |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3452 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
Posted: Mon Nov 06, 2017 9:00 am Post subject: |
|
|
You guys did notice this in the specs I posted??
Quote: | ABNM THICKNESS 0.062 INCHES NOMINAL |
0.062 = 1/16" thick.
These neoprene washers are really gaskets meant to seal and not meant to provide additional flexing of the base. You'll find the collective additional 1/8" of spongy material will allow too much flexing of base. Shop for 1/6" thick sheet or rolls at least 3" wide. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3452 Location: Texas Hill Country
|
|
Back to top |
|
|
Jake266 Member
Joined: Sep 09, 2010 Posts: 51 Location: Missouri
|
Posted: Tue Nov 07, 2017 8:38 am Post subject: |
|
|
I'm going to head to the auto parts store this AM and get the sheet then use my existing one to make a new one. Struck out @ Lowes and also ACE. Had not thought of an auto parts store. Thanks everyone for your input. |
|
Back to top |
|
|
|