View previous topic :: View next topic |
Author |
Message |
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Sun Jun 12, 2016 7:58 am Post subject: GCI Red Oxide III Primer |
|
|
I'm getting ready to apply a second coat of primer to my frame. The frame was blasted before the first coat. It's been 32 hours since my first coat. To achieve a mechanical bond, do I need to block sand it before applying the second coat? Thanks in advance. Bill |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16265 Location: Wisconsin
|
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Sun Jun 12, 2016 10:29 am Post subject: |
|
|
wesk wrote: | Preparations for each paint layer vary between paint manufacturers and between types of paint. neither of which you have shared with us yet. Best course of action is to read the can labels or google the paint manufacturer's web site and read the correct procedure there. | The mfg and product type is in the title of the post. I'm really more interested in getting input from someone who has used this particular product. Practical experience is more important than the spec sheet which does not give the info that I'm requesting. Thanks for the tutorial though. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16265 Location: Wisconsin
|
Posted: Sun Jun 12, 2016 11:19 am Post subject: |
|
|
Here is a good place to get opinions on how someone fared in their use of the paint but you still can't beat starting with the manufacturer's directions for application. Variations in spray equipment, pressures and flow rates, temperatures and humidity will skewer any advice here with the results you can obtain with your own equipment, settings and relative temps/humidity.
For example your 32 hours between first and second coat exceed Gillespie's recommended 16 to 20 hours for 90/94 series red alkyd primer. Gillespie has no requirement to roughen first coat prior to second coat. But your title doesn't tell us which series Gillespie red oxide you are using.
If it is the 90/94 series then the data sheet with the application info is at:
http://www.gillespiecoatings.com/ContentHandler.ashx?ID=13
_________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Sun Jun 12, 2016 11:36 am Post subject: |
|
|
wesk wrote: | Here is a good place to get opinions on how someone fared in their use of the paint but you still can't beat starting with the manufacturer's directions for application. Variations in spray equipment, pressures and flow rates, temperatures and humidity will skewer any advice here with the results you can obtain with your own equipment, settings and relative temps/humidity.
For example your 32 hours between first and second coat exceed Gillespie's recommended 16 to 20 hours for 90/94 series red alkyd primer. Gillespie has no requirement to roughen first coat prior to second coat. But your title doesn't tell us which series Gillespie red oxide you are using.
If it is the 90/94 series then the data sheet with the application info is at:
http://www.gillespiecoatings.com/ContentHandler.ashx?ID=13
|
It's the 100 series and gives only the minimum waiting time for recoat but does not give the maximum time. I received the product sheet with the product. I don't think their web lists it. I suspect I'm outside of the window so that's why I ask the question. I'm prepared to block sand but will wait until they're open tomorrow to ask.
Last edited by Brumbach on Sun Jun 12, 2016 3:17 pm; edited 1 time in total |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16265 Location: Wisconsin
|
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Sun Jun 12, 2016 3:15 pm Post subject: |
|
|
wesk wrote: | If the coat has cured a lot light sanding is usually the routine. | I took the frame to the blaster and immediately primed it with the first coat but didn't finish until late Friday night. I had to be out of town yesterday and therefore had no opportunity to apply the second coat. I was confident I'd have to sand it before applying the second coat due to the extended delay. Guess I was hoping someone on the forum would give me news otherwise. You'd think being retired I would own my own time wouldn't you? Maybe in the next life..... |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16265 Location: Wisconsin
|
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Mon Jun 13, 2016 7:43 am Post subject: |
|
|
Called the manufacturer this morning and was told there is no maximum time for recoating the 100 series primer. I then asked is any surface prep such as sanding or buffing necessary to ensure bonding between coats. They said "no surface prep necessary other than making sure surface is clean and grease free.
What do you think? |
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Thu Jun 16, 2016 8:24 am Post subject: |
|
|
Mfg says no sanding necessary between primer and topcoat (11 SERIES - ALKYD ENAMEL TOPCOAT) provided done within 6 months. What has been your experience? |
|
Back to top |
|
|
|