View previous topic :: View next topic |
Author |
Message |
bamaj Member
Joined: Sep 22, 2013 Posts: 107
|
Posted: Fri Aug 10, 2018 5:06 pm Post subject: Battery hold down |
|
|
Ok so I ordered the battery hold downs fro Midwest and there great but what are the tabs on top of the bracket for? I've looked in TM9-8015-2 page 43 and I see them but there isn't any reference as to what they are used for. Thanks Jeff |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
keats Member
Joined: Apr 14, 2005 Posts: 332 Location: Middletown Ct
|
Posted: Sat Aug 11, 2018 9:24 am Post subject: |
|
|
I don't know what vehicle you have but the M38 battery under the hood has a battery hold down with two tabs with holes in them to attach the hold down to the batter box . See the directions below out of the maintenance manual for the m38'
For some reason the number sizes of bolts didn't copy correctly over but you can get the picture.
b. Battery Maintenance. Refer to TM 9-2857 for specific gravity test, adding water, and cleaning.
c. Battery “A” Removal (fig. 6.
(1) Lift and release the ring latches securing the insulating
box cover and open the cover.
(2) Remove the terminal nut and disconnect the ground
cable from the clamp-type terminal on the negative post. (3) Remove the terminal nut and disconnect the battery-to- battery cable from the clamp-type terminal on the posi-
tive post.
(4) Remove the two wing nuts and flat washers securing
the hold-down frame to the battery, and the wing nuts and flat washers securing the battery box-to-fender straps to the battery box and hold-down frame. Remove the box-to-fender strap bolts and remove the hold-down frame.
(5) Lift the battery straight up and out of the battery box.
Note.Do not use a lifting strap that fastens to the battery posts as it m’ay result in damage to the battery.
d. Battery “A” Installation (fig. 6.
(1) Lower the battery into the battery box, with the battery posts toward the engine side of the box.
Note. Replacement batteries may not be equipped with clamp- type terminals. If not, remove the terminals from the old bat- tery and install on the replacement battery. Be sure that battery posts and terminals are clean.
Figure Battery “A” located in compartment.
(2) Install the hold-down frame and install the two y/l6 x ah bolts through the hold-down frame, the battery box, and the battery box-to-fender strap. Secure the hold- down frame and box-to-fender straps with four s8-inch plain washers and y16-inch wing nuts.
Connect the battery-to-battery cable to the clamp-type terminal on the positive post, and secure with a s-inch terminal nut.
Connect the ground cable to the clamp-type terminal on the negative post, and secure with a a/a-inch terminal nut.
Check polarity (9 below).
Close the insulating box cover and secure with the ring latches. _________________ Gary Keating
1949 C3A, 1952 M38,
1954 M170, 1957 Cj3B |
|
Back to top |
|
|
bamaj Member
Joined: Sep 22, 2013 Posts: 107
|
Posted: Sat Aug 11, 2018 1:38 pm Post subject: |
|
|
Sorry I'm working on m38A1 |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
Posted: Sat Aug 11, 2018 7:18 pm Post subject: |
|
|
These are the brackets you just received from MWM for your M38A1?
This is the M38's forward battery box that Gary referred to. The two short brackets below the box are the two that retain the box to the fender.
This is how your new hold downs are installed. The tabs simply provide a way to limit battery movement during rough off roading. They are not fastened to anything. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
bamaj Member
Joined: Sep 22, 2013 Posts: 107
|
Posted: Sat Aug 11, 2018 9:21 pm Post subject: |
|
|
This is what I have are they correct? |
|
Back to top |
|
|
urbncby Member
Joined: Aug 14, 2018 Posts: 1
|
Posted: Tue Aug 14, 2018 10:29 am Post subject: |
|
|
Do you have link to the batt hold down kit? I didn't see it on their site. Thanks. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
bamaj Member
Joined: Sep 22, 2013 Posts: 107
|
Posted: Wed Aug 15, 2018 4:14 pm Post subject: |
|
|
Looks like I have two of the same one. Correct? |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
bamaj Member
Joined: Sep 22, 2013 Posts: 107
|
Posted: Wed Aug 15, 2018 6:35 pm Post subject: |
|
|
Thanks Wes I will give John a call tomorrow. |
|
Back to top |
|
|
|