View previous topic :: View next topic |
Author |
Message |
idiocrates Member
Joined: Nov 02, 2007 Posts: 437 Location: Seguin, Texas
|
Posted: Tue Apr 20, 2010 10:14 am Post subject: Pulleys mis-aligned |
|
|
I've gotten the new water pump installed on my freshly overhauled F head engine and have been working on getting my 12v alternator adapter built. Now that I have them all together I see where I have some pretty big mis-alignment issues. Just fyi, I'm using all double groove pulleys....so it looks doubly bad. Initial checks indicate that the water pump pulley is too far forward....and in reading some of the archival posts it sound like this is not too unusual. Some of the archived replies suggested pressing the water pump onto the water pump shaft farther. Is this only possible by removing the water pump from the engine and going to the machine shop....or can it be done with a really big hammer while the pump is still on the block (since as I read the instructions the pulley is the last thing pressed on)? Thanks. _________________ Jim
***********************
'?? - M38A-1 |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16265 Location: Wisconsin
|
Posted: Tue Apr 20, 2010 11:52 am Post subject: |
|
|
Both 1803A (WWII) and 1804A (M38) press the shaft into the pulley first. Then press the shaft/pulley assy into the body (This is the ideal point to check pulley alignment), then press this pulley/shaft/housing assy into the assembled impeller/seal assy and finally install clip.
There's quite a bit of clearance between the impeller and the front cylinder so you have no way to brace the impeller and trying to hammer against the small wire clip will destroy the clip and jam some of the clip material between the shaft and housing.
The only sensible method is to remove the pump after you determine accurately how far the pulley must be moved and then remove the clip and brace the back end of the impeller on the press and push the pulley to it's correct location. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Tue Apr 20, 2010 1:26 pm Post subject: |
|
|
Is you drive pulley the type that has a wide front v-groove and narrow rear v-groove? This will cause alignment issues as well. Just checking because I made this mistake in the past. |
|
Back to top |
|
|
idiocrates Member
Joined: Nov 02, 2007 Posts: 437 Location: Seguin, Texas
|
Posted: Tue Apr 20, 2010 3:59 pm Post subject: |
|
|
Yes.....my crank shaft, water pump, and alternator all have the same width pulleys....or maybe I should say.....the same width grooves. I had noted this exception earlier when I was shopping for a new double groove pulley for my alternator and a new water pump and made sure I got everything the same.
Regarding the assembly procedure.....I had originally only looked in the TM9-8015 (correct to 1 Feb 1954) and it definitely lists pressing on the pully as the final step in rebuilding the water pump....although it says nothing about pressing against the impellor and not the water pump housing). After I read Mr. Knettle's reply I looked in the TM9-8014 (correct to 25 Jan 1955) and as he indicated it presses the pulley on to the shaft first and then presses the shaft into the housing. I guess if I had looked at the completed assembly my question would have been mute. Oh well....not like this is the first item I've had to install multiple times...and it probably won't be the last. _________________ Jim
***********************
'?? - M38A-1 |
|
Back to top |
|
|
G740 Member
Joined: Jan 27, 2006 Posts: 499
|
Posted: Tue Apr 20, 2010 5:37 pm Post subject: Pulley |
|
|
Is your water pump pulley a cast type? If so, they are junk. They are not made correctly and you will never get it to align. I have pumps with original pulleys reconditioned to make sure the proper press fit is achieved.
John |
|
Back to top |
|
|
idiocrates Member
Joined: Nov 02, 2007 Posts: 437 Location: Seguin, Texas
|
Posted: Wed Apr 21, 2010 8:10 am Post subject: |
|
|
The water pump pulley appears to be of the machined variety. It came already installed on the pump I bought from Kaiser Willys in NC. I plan on removing the pump from the engine after I take a few measurements and then go to the machine shop to see if they can press the pulley on a little bit more. If they refuse to do it....or we mess sumptin up trying....I'll probably be giving you a call. Are you allowed to tell me on here how much a new pump would be with a double groove pulley? Thanks. _________________ Jim
***********************
'?? - M38A-1 |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16265 Location: Wisconsin
|
|
Back to top |
|
|
G740 Member
Joined: Jan 27, 2006 Posts: 499
|
Posted: Fri Apr 23, 2010 6:11 am Post subject: pulley |
|
|
KW sells parts to the unknowing mv collectors that don't know any better and they get chosen because of their price. Problem is that 9 out 10 times you don't get what you were supposed to and it costs you twice.
The pumps that they are selling have the cast pulley and will not work. They are not cast or machined properly and a pressing will not correct it.
My pumps with original pulley are $115 exchange.
John |
|
Back to top |
|
|
|