Joined: Jan 31, 2012 Posts: 197 Location: West Point, VA
Posted: Mon Jun 03, 2013 7:30 pm Post subject: Dauntless 225 V6 questions.
Hey Guys. I'm considering putting in a Dauntless 225 V6 into my jeep because I want to have fun with my jeep, but keep the exterior looking pretty stock. What would need to be done to make this happen? Here's the info I have so far on the possible buy.
It has a dauntless 225 V6 installed with a new clutch installed on the 90 lbs flywheel. All the running gear is from a 1970 Jeepster to include the engine trans and axels
I'm looking at earlycj5.net but not finding the information needed. I'm assuming I may need some kind of lift as the engine is bigger. A possible engine mounting plate that is modified or will fit the A1. Will it even fit though being the fact it's bigger? I won't have the water pump fan going through the radiator will I because of wheel base being shorter (I'm assuming) than they jeepster?
I just read over on G503 that it'll fit right in with no adjustmemts. Is this correct? I have come across a decent deal on a CJ5 and was considering it for fun factor. Plus I'd like to drive it to work (interstate where the speeds are 70 MPH) Any thoughts and advice? _________________ Dave
52 M38A1
Joined: Jan 31, 2012 Posts: 197 Location: West Point, VA
Posted: Mon Jun 03, 2013 7:32 pm Post subject:
I just realized Wes that you answered the question on the G... Is there anything else I should know besides "If you must change from the F134 to a more modern or powerful engine then there are three that will fit right in with the existing drivetrain and mount space, two of which were already engineered by Willys/Kaiser to fit in there. The Dauntless 225 V6..." _________________ Dave
52 M38A1
I'm looking at earlycj5.net but not finding the information needed. I'm assuming I may need some kind of lift as the engine is bigger. A possible engine mounting plate that is modified or will fit the A1. Will it even fit though being the fact it's bigger? I won't have the water pump fan going through the radiator will I because of wheel base being shorter (I'm assuming) than they jeepster?
I just read over on G503 that it'll fit right in with no adjustmemts. Is this correct? I have come across a decent deal on a CJ5 and was considering it for fun factor. Plus I'd like to drive it to work (interstate where the speeds are 70 MPH) Any thoughts and advice?
_________________
1- You need the engine with the correct bell housing.
2-You do not need to lift anything. The V6 will run in the stock M38A1 chassis and tub just fine.
3-You need the side mount brackets for the frame to replace the L134 brackets. I believe you still have two choices. An old V6 CJ5 or 6 chassis or Advanced adapters/Novak.
4-You need the CJ5 or 6 V6 rear crossmember.
5-You need the V6 CJ5 or 6 radiator.
6-The T86AA or T14 tranny.
7-The 5:38 axles will work but the 4:88 or 3:73 will do much better on the highway.
8-The VJ was used in the early CJ5 which has the exact same distance between the firewall and the gill guard as the M38A1.
9-You'll need the CJ5 or 6 V6 clutch cross shaft and linkage. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
Posted: Tue Jun 04, 2013 6:11 pm Post subject:
The 225 will cool just fine with the stock 4cly radiator. Try to get a t14 transmission, it is much stronger than the t86. I am not sure what cross-member wes is referring to. If he means transmission crossmember the one on my brothers stock 225 v6 cj5 is the same as the one in my m38.
I know the 225 well, my brother has a cj5 with one, and before I bought my m38 I had a cj3a with one swapped in.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum