Author |
Message |
Topic: Adapter plate |
Bobber
Replies: 4
Views: 2733
|
Forum: Technical Knowledge Base Posted: Thu Mar 18, 2021 5:44 pm Subject: Adapter plate |
I put a Kubota in mine. I miss the sound of the L134. https://www.youtube.com/watch?v=OOQ1OkXPWgI&ab_channel=RustyBell |
Topic: M38 parts wanted |
Bobber
Replies: 3
Views: 5321
|
Forum: Wanted Posted: Thu Aug 08, 2019 11:07 pm Subject: Parts wanted |
PM sent |
Topic: Down to nuts and bolts.... |
Bobber
Replies: 9
Views: 7003
|
Forum: Technical Knowledge Base Posted: Mon Jan 28, 2019 12:13 pm Subject: Down to nuts and bolts.... |
My arctic top came with brass screws in the door handles. Didn't see any brass screws when I did my off frame restoration. |
Topic: Transmission tower leaking |
Bobber
Replies: 4
Views: 5234
|
Forum: Technical Knowledge Base Posted: Fri Jan 18, 2019 6:14 pm Subject: Transmission tower leaking |
I filled the trans and the TC to the height of the fill plug. When oil starts coming out where you fill it, stop pumping in oil. I didn't clamp either end of the boot. The tranny is sitting up about 1 ... |
Topic: Transmission tower leaking |
Bobber
Replies: 4
Views: 5234
|
Forum: Technical Knowledge Base Posted: Wed Jan 16, 2019 1:21 pm Subject: Transmission tower leaking |
I thought my trans was leaking when I poked my head under the Jeep. After taking the floor out I realized all the fluid was coming from the trans tower boot. So I think the fluid is being slung up in ... |
Topic: M38 T90 Transmission Leak at Counter Shaft |
Bobber
Replies: 9
Views: 8139
|
Forum: Technical Knowledge Base Posted: Sat Jul 28, 2018 9:13 pm Subject: M38 T90 Transmission Leak at Counter Shaft |
I used Ultra Black, Sensor Safe in the same place and ever place I thought it might leak. I have no leaks in either tranny or Trans Case. I was clean with it so it didn't ooze out too much. Good stu ... |
Topic: Parting out L134 |
Bobber
Replies: 0
Views: 5127
|
Forum: Auctions Posted: Tue May 22, 2018 5:42 pm Subject: Parting out L134 |
Have many engine parts for 24 volt L134. tin, carb, starter, alt, dist. etc. My block was found to be cracked along with my backup block. So rather than source another block that may crack, I chose ... |
Topic: Got my dad's jeep back on the road!!!! |
Bobber
Replies: 3
Views: 6982
|
Forum: Jeep Project Threads Posted: Sat May 12, 2018 3:48 pm Subject: Got my dad's jeep back on the road!!!! |
Very cool. |
Topic: Cracked blocks |
Bobber
Replies: 11
Views: 9887
|
Forum: Technical Knowledge Base Posted: Thu Mar 29, 2018 9:09 pm Subject: Cracked blocks |
Cracks were on top between 2&3 cyinders. Both blocks. |
Topic: Cracked blocks |
Bobber
Replies: 11
Views: 9887
|
Forum: Technical Knowledge Base Posted: Thu Mar 29, 2018 8:29 pm Subject: Cracked blocks |
Long story short, My block was sent to the shop. They magnafluxed it and found a crack. I had a second block in the corner and sent that one in. It too was cracked in the same place. The shop said ... |
Topic: Low compression |
Bobber
Replies: 15
Views: 13904
|
Forum: Technical Knowledge Base Posted: Mon Feb 26, 2018 1:29 pm Subject: Low compression |
Ya thanks, It's been decked before cause the serial number was gone when I got it. I hope there is enough to work with. Do you think that the head gasket being bad would cause the oil to always be ... |
Topic: Low compression |
Bobber
Replies: 15
Views: 13904
|
Forum: Technical Knowledge Base Posted: Sun Feb 25, 2018 11:28 pm Subject: Low compression |
Because I have no idea, how does this happen? How do you prevent this?\
Thanks for information. |
Topic: Low compression |
Bobber
Replies: 15
Views: 13904
|
Forum: Technical Knowledge Base Posted: Sun Feb 25, 2018 10:19 pm Subject: Low compression |
http://i66.tinypic.com/euoefa.jpg I got here using an outside way. My kid helped me so I don't know. But here is the block. You can see I rubbed the valves with my finger. |
Topic: Low compression |
Bobber
Replies: 15
Views: 13904
|
Forum: Technical Knowledge Base Posted: Sun Feb 25, 2018 10:01 pm Subject: Low compression |
Air coming from crankcase, pulled head off. Carbon build up on pistons not much carbon build up on valves. No.3 cylinder valves looked a lot cleaner than the rest ( less carbon). So since I'm here, ... |
Topic: Low compression |
Bobber
Replies: 15
Views: 13904
|
Forum: Technical Knowledge Base Posted: Sun Feb 25, 2018 12:14 am Subject: Low compression |
That's what I did this afternoon. I've done some reading in a civvy manual and followed the trouble shooting area. I removed the intake/exhaust manifold, valve cover. I was hoping for a broken sprin ... |
|