| Author |
Message |
 Topic: Electronic ignition for distributor |
Jason86
Replies: 1
Views: 3267
|
 Forum: Technical Knowledge Base Posted: Thu Jul 12, 2018 3:04 pm Subject: Electronic ignition for distributor |
| Are the electronic ignition (solid state) kits that were made back in the 80s for converting over from points to electronic ignition worth installing into the 24v distributor? I see some NOS kits bein ... |
| Topic: Fuel pump question |
Jason86
Replies: 14
Views: 12402
|
Forum: Technical Knowledge Base Posted: Thu Jun 21, 2018 10:59 pm Subject: Fuel pump question |
| Then and Now Automotive was asking on his Facebook page if there were any videos that people wanted him to make, so I asked him to make one showing how they preloaded the pumps when they did a rebuild ... |
| Topic: Restauration bolts, screw and nuts. |
Jason86
Replies: 3
Views: 4745
|
Forum: Technical Knowledge Base Posted: Wed Jun 20, 2018 10:17 pm Subject: Restauration bolts, screw and nuts. |
| Wes I was just thinking about restoring the hardware on the jeep or sending it out to get yellow zinc plated for stuff that will possibly get remover or need repairs later like covers or drain plugs. ... |
| Topic: Stock lug nuts size |
Jason86
Replies: 4
Views: 4581
|
Forum: Technical Knowledge Base Posted: Wed Jun 13, 2018 1:19 am Subject: Stock lug nuts size |
| OK thank you for bringing that up Wes that is good to know. I'll be ordering the 3/4 in. ones. |
| Topic: Stock lug nuts size |
Jason86
Replies: 4
Views: 4581
|
Forum: Technical Knowledge Base Posted: Wed Jun 13, 2018 12:52 am Subject: Stock lug nuts size |
Hahahah. I see what you did there.  yep that is one way of finding out, I didn't think that one through.  Thanks again Wes |
| Topic: Stock lug nuts size |
Jason86
Replies: 4
Views: 4581
|
Forum: Technical Knowledge Base Posted: Tue Jun 12, 2018 9:12 pm Subject: Stock lug nuts size |
| Question for the experienced pros, did the 1953 m38a1 come from the factory with 3/4 or 13/16 inch lug nuts? Looked in the Ord 9 all parts book but it didn't list the OD size just thread size and qua ... |
| Topic: Restamping engine block |
Jason86
Replies: 4
Views: 4218
|
Forum: Technical Knowledge Base Posted: Thu May 24, 2018 12:21 am Subject: Restamping engine block |
| Did they restamp the F 134 engine blocks behind the water pump after a engine rebuild with the MD engine # ? Can I assume that if the engine # starting with MD is still visible that the engine block h ... |
| Topic: No oil to head, F134 (Solved) |
Jason86
Replies: 14
Views: 12729
|
Forum: Technical Knowledge Base Posted: Mon May 21, 2018 11:27 pm Subject: No oil to head, F134 (Solved) |
| Wes thank you for bringing up the subject about the block. I knew about the crankshaft needing to be remachined to spec to accept the neoprene seal from scanning other posts but I guess I overlooked t ... |
| Topic: Main shaft gear style |
Jason86
Replies: 8
Views: 7338
|
Forum: Technical Knowledge Base Posted: Mon May 07, 2018 4:07 pm Subject: Main shaft gear style |
OK thank you Wes for correcting the photo link I was having a hard time with that and I couldn't figure out how to make sure the photo wasn't over 250k.
So can either one of these 2 styles be used ... |
| Topic: Main shaft gear style |
Jason86
Replies: 8
Views: 7338
|
Forum: Technical Knowledge Base Posted: Mon May 07, 2018 1:44 am Subject: Main shaft gear style |
[img]http://www.willysmjeeps.com/v2/modules.php?set_albumName=album592&id=Screenshot_2018_05_05_20_32_23_1&op=modload&name=gallery&file=index&include=view_photo.php[/img]
The li ... |
| Topic: Main shaft gear style |
Jason86
Replies: 8
Views: 7338
|
Forum: Technical Knowledge Base Posted: Sun May 06, 2018 7:44 pm Subject: Main shaft gear style |
| Sorry Wes I should have gone by the parts book. It would actually be part "Z" in your photo, Spur, Gear WO-A10469. It appears there are 2 different styles only thing different is the backside. I just ... |
| Topic: Main shaft gear style |
Jason86
Replies: 8
Views: 7338
|
Forum: Technical Knowledge Base Posted: Sun May 06, 2018 1:28 am Subject: Main shaft gear style |
| I see there are 2 different types of main shaft gears for the D18, both are the same gear count and practically identical but one style has a square shoulder on the backside the other a 45 degree cham ... |
| Topic: Tranny/Transfer case sharing lube |
Jason86
Replies: 13
Views: 16871
|
Forum: Technical Knowledge Base Posted: Sun Jul 30, 2017 10:34 pm Subject: Tranny/Transfer case sharing lube |
| If rebuilding one or the other would it be a bad idea to block the passage holes while it's apart to keep the two from sharing fluid? Then you wouldn't have to worry about over filling the transfer ca ... |
| Topic: Tranny/Transfer case sharing lube |
Jason86
Replies: 13
Views: 16871
|
Forum: Technical Knowledge Base Posted: Mon Jul 24, 2017 11:53 pm Subject: Tranny/Transfer case sharing lube |
| Thank you Wes for taking the time to go into detail fully explaining everything and Don for the link! I'm more of a visual learner so the pictures help alot. I'm going to be needing a larger storage d ... |
| Topic: F134 engine overhaul guestions |
Jason86
Replies: 3
Views: 6080
|
Forum: Technical Knowledge Base Posted: Wed Jul 12, 2017 11:04 am Subject: F134 engine overhaul guestions |
| Thank you wesk that's exactly what I wad looking for and wanted to hear. I looked for that info but guess I was looking in the wrong books. |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
