Author |
Message |
Topic: Is there a hole under the gas tank? |
Jeff_H
Replies: 8
Views: 8483
|
Forum: Technical Knowledge Base Posted: Wed Oct 25, 2006 6:26 am Subject: Is there a hole under the gas tank? |
Ryan
ABout midway down this page http://www.m38jeepproject.com/Body%20Work%202.html are images of when I changed my floor that show the gas tank drain plug hole.
Jeff |
Topic: Douglass Connectors |
Jeff_H
Replies: 7
Views: 9867
|
Forum: Technical Knowledge Base Posted: Thu Aug 17, 2006 8:55 pm Subject: Douglass Connectors |
Soldering will work just fine for a show jeep. The reason the military went with crimp connectors was vibration has a tendency to cause soldered leads to break at the point the solder quits in the wir ... |
Topic: Douglass Connectors |
Jeff_H
Replies: 7
Views: 9867
|
Forum: Technical Knowledge Base Posted: Thu Aug 17, 2006 4:55 pm Subject: Douglass Connectors |
If you're wanting a tool for collecting they come up on e-bay from time to time. If you're looking to make a connection, I solder mine on as I believe it makes a better connection and they are remova ... |
Topic: Is there a hole under the gas tank? |
Jeff_H
Replies: 8
Views: 8483
|
Forum: Technical Knowledge Base Posted: Tue Aug 15, 2006 3:35 pm Subject: Is there a hole under the gas tank? |
Yes
Where the drain plug is I beleive.
Jeff |
Topic: Restoration site |
Jeff_H
Replies: 50
Views: 52092
|
Forum: Announcements, News, Humor Posted: Tue Aug 15, 2006 5:08 am Subject: Restoration site |
More updates on site.
Jeff |
Topic: M38 Brake Adjustment |
Jeff_H
Replies: 6
Views: 8202
|
Forum: Technical Knowledge Base Posted: Tue Aug 15, 2006 5:07 am Subject: M38 Brake Adjustment |
Ryan
To undo the locking nut I bought a 3/4 inch offset box wrench and ground it down, top and bottom, until it fit under the 4 bolds on the bottom of the square block (king pin keepers?) which mak ... |
Topic: Restoration site |
Jeff_H
Replies: 50
Views: 52092
|
Forum: Announcements, News, Humor Posted: Wed Aug 09, 2006 11:02 pm Subject: Restoration site |
Site updated. www.m38jeepproject.com
Engine back, installed and running.
YEAH!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Jeff |
Topic: Getting closer to a running chassis. Questions: |
Jeff_H
Replies: 9
Views: 9362
|
Forum: Technical Knowledge Base Posted: Sun Jul 16, 2006 9:22 pm Subject: Getting closer to a running chassis. Questions: |
Have a look this page of my re-build site to see how I refurbished my gauges.
http://www.m38jeepproject.com/electrical%201.html
I found sand blasting the faces and then wet sanding through progr ... |
Topic: How much paint will I use? |
Jeff_H
Replies: 2
Views: 4817
|
Forum: Technical Knowledge Base Posted: Sun Jul 16, 2006 9:17 pm Subject: How much paint will I use? |
Not sure how much if you do it by brush, but by spraying two gallons will give you enough to do the job and some left over for touch-up, gas cans, friends parts (once they find out you have OD paint), ... |
Topic: Pinhole leak in block...what to do?? |
Jeff_H
Replies: 7
Views: 11868
|
Forum: Technical Knowledge Base Posted: Wed Jul 12, 2006 3:49 am Subject: Pinhole leak in block...what to do?? |
Have a look at this thread @ G503.com On page 2 it has an associated site link that may offer some hope.
http://www.g503.com/forums/viewtopic.php?t=73348
Jeff |
Topic: Restoration site |
Jeff_H
Replies: 50
Views: 52092
|
Forum: Announcements, News, Humor Posted: Thu Jun 08, 2006 11:23 pm Subject: Restoration site |
Added some more photo's and made some site upgrades as well. Good news ... got the engine in and running!!! Bad news ... didn't run all that well and investigation determined a re-build was in order s ... |
Topic: WillysMJeeps Map |
Jeff_H
Replies: 15
Views: 20247
|
Forum: Announcements, News, Humor Posted: Thu Jun 08, 2006 8:06 pm Subject: WillysMJeeps Map |
Lucky 13!!!
Jeff |
Topic: Generator to regulator cable |
Jeff_H
Replies: 15
Views: 16721
|
Forum: Technical Knowledge Base Posted: Wed May 31, 2006 12:30 pm Subject: Generator to regulator cable |
Jeff, where did you purchase your cable?
Ken
Sorry can't help, it came with the jeep!
Jeff |
Topic: Generator to regulator cable |
Jeff_H
Replies: 15
Views: 16721
|
Forum: Technical Knowledge Base Posted: Tue May 30, 2006 9:16 pm Subject: Generator to regulator cable |
here is what it looks like on my M38. The "loop" is just behind the tub brace thingy (what the heck is that actually called anyway?).
http://www.m38jeepproject.com/images/IMG_7460sm.JPG
Jeff |
Topic: How is this for a patch panel!! |
Jeff_H
Replies: 2
Views: 5228
|
Forum: Technical Knowledge Base Posted: Sat May 20, 2006 10:13 pm Subject: How is this for a patch panel!! |
Way to screw up the future!!!
100 years from now when some one sands your jeep down during a restoration and finds that panel, this site and the G503 forum will erupt with "experts" swearing that j ... |
|