Author |
Message |
Topic: Easy bleeders? |
Mjfire1949
Replies: 1
Views: 3869
|
Forum: Technical Knowledge Base Posted: Wed Sep 30, 2015 4:45 pm Subject: Easy bleeders? |
1952 M38, 24 volt, Serial #65666, North Texas. Any opinions on using "Easy Bleeders" on my M38 other than the expense? |
Topic: Oil leak |
Mjfire1949
Replies: 5
Views: 7779
|
Forum: Technical Knowledge Base Posted: Sun Sep 27, 2015 10:34 am Subject: Oil leak |
The seal that was in the vehicle was a lot wider than the one I got from Midwest. By "destroyed", I mean that the narrow part of the seal that goes into the small groove was completely torn away from ... |
Topic: Oil leak |
Mjfire1949
Replies: 5
Views: 7779
|
Forum: Technical Knowledge Base Posted: Sat Sep 26, 2015 9:58 pm Subject: Oil leak |
Yes, unfortunitly it is motor oil. The transfer was leaking, but only needed to be tightened. The guy I bought it from never heard of a torque wrench. Most of the leaks were due to loose bolts. I ... |
Topic: Oil leak |
Mjfire1949
Replies: 5
Views: 7779
|
Forum: Technical Knowledge Base Posted: Sat Sep 26, 2015 3:41 pm Subject: Oil leak |
'52 M38, 24 volt, Serial # 65666, North Texas. Well, I got the rear main seal replaced with one from Midwest. The seal that was in there was destroyed. Still have a small oil leak from the bell hous ... |
Topic: Correct length for crankshaft pulley guard bolts |
Mjfire1949
Replies: 10
Views: 10075
|
Forum: Technical Knowledge Base Posted: Wed Sep 23, 2015 11:32 am Subject: Message below the picture. |
Yes Wes, I know the manual is free to download. This is the best forum type vehicle web site I've ever seen. I just want a hard copy to keep by the head when I take my daily constitutional. Thanks a ... |
Topic: Correct length for crankshaft pulley guard bolts |
Mjfire1949
Replies: 10
Views: 10075
|
Forum: Technical Knowledge Base Posted: Tue Sep 22, 2015 10:49 pm Subject: Pulley cover bolts |
Thanks Wes. ORD 9 SNL G-740 is the one manual I have not purchased. I didn't realize it had that many pictures. I will be ordering it this week. Thanks again for your priceless knowledge. |
Topic: Correct length for crankshaft pulley guard bolts |
Mjfire1949
Replies: 10
Views: 10075
|
Forum: Technical Knowledge Base Posted: Tue Sep 22, 2015 11:44 am Subject: Correct length for crankshaft pulley guard bolts |
1952 M38, 24 volt, L134, #65666, North Texas. I'm in the process of buttoning up after replacing the rear main seal. I used the seal from Midwest Military. When I removed the pulley guard, I notice ... |
Topic: Crankshaft Pulley Guard Spacers |
Mjfire1949
Replies: 2
Views: 5069
|
Forum: Technical Knowledge Base Posted: Tue Sep 15, 2015 11:57 am Subject: Crankshaft Pulley Guard Spacers |
1952 M38, 4-134 L, 24 volt, Serial # 65666, North Texas. Does anyone know where I can purchase the spacers that fit the crankshaft pulley shield bolts? I dropped the pan to install a new pan gasket ... |
Topic: Ball bearing inside YS637 carb |
Mjfire1949
Replies: 2
Views: 4806
|
Forum: Technical Knowledge Base Posted: Thu May 21, 2015 10:03 pm Subject: Ball bearing inside YS637 carb |
Thanks Wes. I thought that's where it went, but I would be guessing. I will bookmark these pics. Thanks again. |
Topic: Ball bearing inside YS637 carb |
Mjfire1949
Replies: 2
Views: 4806
|
Forum: Technical Knowledge Base Posted: Thu May 21, 2015 10:18 am Subject: Ball bearing inside YS637 carb |
1952 Willys M38, 24 volt, #65666. I had surgery over the winter and was only able to start my M38 every couple of weeks and let it idle. The first time I drove it I barely made it home. The fuel fi ... |
Topic: M38 Fuel Filler Neck |
Mjfire1949
Replies: 7
Views: 10087
|
Forum: Technical Knowledge Base Posted: Tue Apr 21, 2015 9:16 pm Subject: M38 Fuel Filler Neck |
Thanks for the heads up, Wes. There is nothing wrong with the tank currently on the jeep other than I can't use a sending unit with it. I ran out of gas a couple of weeks ago and had a knee jerk. I ... |
Topic: M38 Fuel Filler Neck |
Mjfire1949
Replies: 7
Views: 10087
|
Forum: Technical Knowledge Base Posted: Tue Apr 21, 2015 7:07 pm Subject: M38 Fuel Filler Neck |
1952 Willys M38 #65666, 24 Volt. I was about to order a new gas tank for my M38. Does anyone know if the filler neck is available for purchase? I'm not seeing them anywhere. I don't want to spen ... |
Topic: M38 radio |
Mjfire1949
Replies: 7
Views: 14334
|
Forum: Technical Knowledge Base Posted: Tue Oct 21, 2014 8:34 pm Subject: M38 radio |
I'll get a pic in the morning. Looks like the bracket # is MP-50. |
Topic: M38 radio |
Mjfire1949
Replies: 7
Views: 14334
|
Forum: Technical Knowledge Base Posted: Tue Oct 21, 2014 8:15 pm Subject: M38 radio |
It is a whip style antenna, 10'-12' long. It is mounted on a flat bracket which sits above the left rear brake light and to the left about midpoint of the gas can. If this is not enough information, ... |
Topic: M38 radio |
Mjfire1949
Replies: 7
Views: 14334
|
Forum: Technical Knowledge Base Posted: Tue Oct 21, 2014 2:35 pm Subject: M38 radio |
Does anyone have any suggestions on where to find a period correct radio and mount for a '52 M38? It doesn't have to be working, as it is just for looks. I already have an antenna. |
|