Author |
Message |
Topic: M38CDN Takeout Dash |
boucher
Replies: 2
Views: 6015
|
Forum: For Sale Posted: Thu Mar 03, 2011 9:50 am Subject: M38 CDN wiring harness |
Hello from Ottawa:
Looking for M38 wiring harness , know of any ???
Thanks
Peter
greengear@ymail.com
greengear.usedottawa.com
613-620-5244 |
Topic: 1953 M38 CDN CLUTCH DISK PART #??? |
boucher
Replies: 4
Views: 17104
|
Forum: Technical Knowledge Base Posted: Mon Jun 16, 2008 12:52 pm Subject: 1953 M38 CDN CLUTCH DISK PART #??? |
Called my local NAPA to see if they carried a clutch disk for the M38, he wasn't able to pull it up .
Does anyone know what the part # for it??
Thanks
Peter(Ottawa)
P.S. Pulled the head ,t ... |
Topic: DONOR LHEAD LEAK DOWN TEST RESULTS |
boucher
Replies: 1
Views: 3856
|
Forum: Technical Knowledge Base Posted: Thu Jun 12, 2008 9:39 am Subject: DONOR LHEAD LEAK DOWN TEST RESULTS |
HELLO:
I PERFORMED A QUICK LEAK DOWN TEST ON ALL CYLINDERS LAST NIGHT AND THE RESULTS WERE ALL THE SAME.
HISSING COULD BE HEARD FROM ALL EXHAUST VALVES. COULD THIS BE AS SIMPLE AS CARBON BUILDUP ... |
Topic: UPDATE ON MY DONOR GENERATOR LHEAD |
boucher
Replies: 4
Views: 5616
|
Forum: Technical Knowledge Base Posted: Tue Jun 10, 2008 10:44 am Subject: UPDATE ON MY DONOR GENERATOR LHEAD |
Thanks Wes, as always you provide excellent feedback.
Peter (Ottawa) |
Topic: UPDATE ON MY DONOR GENERATOR LHEAD |
boucher
Replies: 4
Views: 5616
|
Forum: Technical Knowledge Base Posted: Tue Jun 10, 2008 6:25 am Subject: UPDATE ON MY DONOR GENERATOR LHEAD |
I installed the rear plate to accomodate the starter , this past weekend. So last night was time to try a compression test and the results are less than impressive:
#1 30 PSI
#2 0 PSI
#3 60 PSI ... |
Topic: LHEAD FRONT ENGINE PLATE generator to M38 |
boucher
Replies: 3
Views: 5677
|
Forum: Technical Knowledge Base Posted: Fri Jun 06, 2008 12:46 pm Subject: LHEAD FRONT ENGINE PLATE generator to M38 |
Wes:
Thanks.
If I try option 3 or 4 can I still use the original fuel/vacuum pump? Or do I have to convert to a civy fuel pump?
Cheers
Peter (Ottawa) |
Topic: LHEAD FRONT ENGINE PLATE generator to M38 |
boucher
Replies: 3
Views: 5677
|
Forum: Technical Knowledge Base Posted: Fri Jun 06, 2008 9:49 am Subject: LHEAD FRONT ENGINE PLATE generator to M38 |
The front engine plate is different on the generator engine compared with the M38 engine. Both brackets that attach to the frame face backwards on the gen set and only 1 faces backwards on the M38 .
... |
Topic: Found L Head Generator |
boucher
Replies: 2
Views: 4620
|
Forum: Technical Knowledge Base Posted: Wed Jun 04, 2008 7:52 am Subject: Found L Head Generator |
It turned out to be a loose bolt on the flywheel to crank, that was rubbing. Tightened it up ,now it's rotation freely.
Thanks
Peter (Ottawa) |
Topic: Found L Head Generator |
boucher
Replies: 2
Views: 4620
|
Forum: Technical Knowledge Base Posted: Tue Jun 03, 2008 9:30 am Subject: Found L Head Generator |
I finally found a donor candidate for my 1952 M38 CDN restoration. It comes from a stationary gen set with what appears to be magneto distributor set up.
I can hand turm the flywheel almost 1 compl ... |
Topic: How To Square Up the tub 1952 M38 CDN |
boucher
Replies: 4
Views: 6047
|
Forum: Technical Knowledge Base Posted: Tue Mar 04, 2008 2:41 pm Subject: How To Square Up the tub 1952 M38 CDN |
Thanks, much appreciated. |
Topic: How To Square Up the tub 1952 M38 CDN |
boucher
Replies: 4
Views: 6047
|
Forum: Technical Knowledge Base Posted: Mon Feb 25, 2008 12:23 pm Subject: How To Square Up the tub 1952 M38 CDN |
Thanks Wes
Unfortunately I can't make out the spelling on the bottom photo, even when I enlarge it.
Peter |
Topic: How To Square Up the tub 1952 M38 CDN |
boucher
Replies: 4
Views: 6047
|
Forum: Technical Knowledge Base Posted: Sat Feb 23, 2008 7:37 am Subject: How To Square Up the tub 1952 M38 CDN |
Hello:
I took my tub off a while back and am now trying to figure out how to line it up properly before I tack in the floors , hat channels ,etc....
I'm bending/fabricating all pieces and the or ... |
Topic: M38 CDN PRESSURE SWITCH , MASTER CYLINDER |
boucher
Replies: 3
Views: 6346
|
Forum: Technical Knowledge Base Posted: Mon Jan 28, 2008 7:42 am Subject: M38 CDN PRESSURE SWITCH , MASTER CYLINDER |
HELLO:
DOES ANYONE KNOW THE NAPA PART NUMBER FOR THE PRESSURE SWITCH ATTACHED TO THE BRAKE MASTER CYLINDER???
THANKS
PETER(OTTAWA) |
Topic: Still Need Frame Info 53 M38 CDN |
boucher
Replies: 7
Views: 9844
|
Forum: Technical Knowledge Base Posted: Mon Nov 19, 2007 7:52 am Subject: Still Need Frame Info 53 M38 CDN |
Thanks for the info.
Now that I know it's for the engine stay cable, does anyone know where the other end of the cable attaches?
Thanks ,
Peter (Ottawa) |
Topic: Still Need Frame Info 53 M38 CDN |
boucher
Replies: 7
Views: 9844
|
Forum: Technical Knowledge Base Posted: Sun Oct 28, 2007 7:06 am Subject: Still Need Frame Info 53 M38 CDN |
Anyone know the dimensions for the frame part that the brake return spring attaches (height/shape/size of hole/etc...) ???
I welded a piece on but need to shape it to the correct dimensions.
Than ... |
|