Author |
Message |
Topic: Always problems with the ignition coil |
c90001
Replies: 5
Views: 7699
|
Forum: Technical Knowledge Base Posted: Fri Apr 13, 2018 2:33 am Subject: Always problems with the ignition coil |
If I can not get a coil then I can possibly resort to this solution. I've already tried it with a 12 volt coil, but the put in then 12 volts. But I thought that the ignition temperature is not the sam ... |
Topic: Always problems with the ignition coil |
c90001
Replies: 5
Views: 7699
|
Forum: Technical Knowledge Base Posted: Fri Apr 13, 2018 2:20 am Subject: Always problems with the ignition coil |
Hello Wesk, with my last coil I had no problems. I'm glad to hear that I was already desperate what's going on with the engine. Is there a possibility to buy a better quality and where?
And you kno ... |
Topic: quality of spare parts Accelerator Pedal Rubber Socket |
c90001
Replies: 3
Views: 4180
|
Forum: Technical Knowledge Base Posted: Fri Apr 13, 2018 2:12 am Subject: quality of spare parts Accelerator Pedal Rubber Socket |
I bought a Accelerator Pedal Rubber Socket for my G740 and after one year it is broken. http://willysmjeeps.com/v2/modules/gallery/albums/album579/Composite.sized.jpg
Unfortunately this rubber is no ... |
Topic: Always problems with the ignition coil |
c90001
Replies: 5
Views: 7699
|
Forum: Technical Knowledge Base Posted: Fri Apr 13, 2018 1:09 am Subject: Always problems with the ignition coil |
Unfortunately, I forget to turn off the ignition key and then burns the electronic ignition and the ignition coil.
Now I have the problem that I have after changing from 2 ignition coils always after ... |
Topic: Electronic Ignition convertion |
c90001
Replies: 7
Views: 8697
|
Forum: Technical Knowledge Base Posted: Fri Apr 13, 2018 12:42 am Subject: need the hall effect sensor a condenser |
Since I burn the contacts too fast, I have also installed the electronic version of the m151A2. Only I'm not sure if I still need the big capacitor. That was only for the break-off sparks and that sho ... |
Topic: M38 electrical problem |
c90001
Replies: 8
Views: 8773
|
Forum: Technical Knowledge Base Posted: Wed May 10, 2017 7:42 am Subject: M38 electrical problem |
so i need the resistor with 95 ohm but i think its not possible to find, |
Topic: M38 electrical problem |
c90001
Replies: 8
Views: 8773
|
Forum: Technical Knowledge Base Posted: Wed May 10, 2017 7:35 am Subject: M38 electrical problem |
but the themp sending was for the G740 and this modell has 24Volt |
Topic: M38 electrical problem |
c90001
Replies: 8
Views: 8773
|
Forum: Technical Knowledge Base Posted: Wed May 10, 2017 7:30 am Subject: M38 electrical problem |
i bought all pices and and before nothing in the car was original. i bought also all gaugs and they have no resister. i bought all new pices for the g740 but same pices show only m38. |
Topic: M38 electrical problem |
c90001
Replies: 8
Views: 8773
|
Forum: Technical Knowledge Base Posted: Wed May 10, 2017 5:58 am Subject: M38 electrical problem |
thank you so much for your information, i will buy a old regulator and than all will be working. |
Topic: M38 electrical problem |
c90001
Replies: 8
Views: 8773
|
Forum: Technical Knowledge Base Posted: Wed May 10, 2017 3:04 am Subject: M38 electrical problem |
Hello everyone who is expert with the Elektirk of the m38 ?
I have installed new cables and a new generator and new regulator (26640473-03 Vap air).
The tank gaug and the pressure gauge are working ... |
Topic: Particles fallen into the m38 engine |
c90001
Replies: 6
Views: 7884
|
Forum: Technical Knowledge Base Posted: Mon Mar 27, 2017 5:14 am Subject: Particles fallen into the m38 engine |
It has again tried with the big dyn magnet and it has worked. The part is out there.
With such a strong magnet under the oil pan has it worked. I had pushed it first against the oil filter, so it had ... |
Topic: Particles fallen into the m38 engine |
c90001
Replies: 6
Views: 7884
|
Forum: Technical Knowledge Base Posted: Sun Mar 26, 2017 6:36 am Subject: Particles fallen into the m38 engine |
Brian,it is made of iron. I have already tried to go with a dyn magnet along the ground but without success |
Topic: Particles fallen into the m38 engine |
c90001
Replies: 6
Views: 7884
|
Forum: Technical Knowledge Base Posted: Sun Mar 26, 2017 4:21 am Subject: Particles fallen into the m38 engine |
In the hole from the oil dipstick is a 1.5 cm metal clamp fallen. I would therefore not so gladly unscrew the oil pan and hope it flows out at the next oil change. The question is whether something c ... |
Topic: connectors |
c90001
Replies: 5
Views: 7328
|
Forum: Wanted Posted: Mon Jan 30, 2017 10:22 pm Subject: connectors |
Do you mean the metal douglas connector are not original for my m38 g740 So for a more modern vehicle?
This would be very bad the cables have cost me 1200Dollar.
[img]http://www.directupload.net/ ... |
Topic: connectors |
c90001
Replies: 5
Views: 7328
|
Forum: Wanted Posted: Mon Jan 30, 2017 12:43 pm Subject: connectors |
I will replace all electric in my jeep and i need all connectors.
Someone has an idea where i can buy about 80 pieces cheap?
I need about 15 pc from A and about 80 pc from G.
http://fs5.directu ... |
|