| Author |
Message |
 Topic: Pitman arm to pitman shaft orientation problem. |
jameydan
Replies: 10
Views: 12838
|
 Forum: Technical Knowledge Base Posted: Tue Apr 24, 2012 12:00 am Subject: Pitman arm to pitman shaft orientation problem. |
| "This is not true if you are using the correct manual. TM 9-8012 and TM 9-8014 say to reassemble a sector and pitman arm that were origianally a matched pair use the match marks. It then says if you h ... |
| Topic: Pitman arm to pitman shaft orientation problem. |
jameydan
Replies: 10
Views: 12838
|
Forum: Technical Knowledge Base Posted: Mon Apr 23, 2012 1:05 pm Subject: Pitman arm to pitman shaft orientation problem. |
John,
Thanks for the advice and your method seems quite logical. I will give that method a try tonight or tomorrow. The pitman arm and the steering gear both had alignment marks chiseled into the ... |
| Topic: Power-Trax "Lock-right" or Dana powr-lok in a Dana |
jameydan
Replies: 3
Views: 7115
|
Forum: Technical Knowledge Base Posted: Sun Apr 22, 2012 10:35 pm Subject: Power-Trax "Lock-right" or Dana powr-lok in a Dana |
| I had a lock right in the front end of a more modern jeep. With out locking hubs, your on road steering will stink - mine would hop, skip, and drag tires and all the while the locker would be making ... |
| Topic: Pitman arm to pitman shaft orientation problem. |
jameydan
Replies: 10
Views: 12838
|
Forum: Technical Knowledge Base Posted: Sun Apr 22, 2012 9:46 pm Subject: Pitman arm to pitman shaft orientation problem. |
DtD,
Thanks for the info, now I hope I can get it off and moved easy enough. I will let you know if I need more info. I think where I went wrong with indexing the pitman arm, was where the manual ... |
| Topic: Pitman arm to pitman shaft orientation problem. |
jameydan
Replies: 10
Views: 12838
|
Forum: Technical Knowledge Base Posted: Sun Apr 22, 2012 11:50 am Subject: Pitman arm to pitman shaft orientation problem. |
| I ran into a little trouble with aligning my pitman arm on the steering gear. I bought a rebuilt steering gear form John at MWM. I took my pitman arm and mounted it as best as possible according to ... |
| Topic: Midwest Mil rebuilt carb |
jameydan
Replies: 10
Views: 16361
|
Forum: M Series Parts Supply & Service Review Posted: Fri Dec 16, 2011 7:40 pm Subject: Midwest Mil rebuilt carb |
| I finished installing my rebuilt carb on my M38A1. I purchased it at MWM, and could not be happier! After rebuilding my original once, with a "quality" kit, and suffering with consistent fuel issues ... |
| Topic: M38A1 vs M38 Carb base gasket and diffuser |
jameydan
Replies: 4
Views: 6567
|
Forum: Technical Knowledge Base Posted: Tue Dec 06, 2011 3:30 pm Subject: M38A1 vs M38 Carb base gasket and diffuser |
Wes,
Great info on the choice to use a sealant or not. I was leaning towards not, as I did not see anything that indicated to use it in the TM manuals. I spent a lot of time last night looking th ... |
| Topic: M38A1 vs M38 Carb base gasket and diffuser |
jameydan
Replies: 4
Views: 6567
|
Forum: Technical Knowledge Base Posted: Mon Dec 05, 2011 11:39 pm Subject: M38A1 vs M38 Carb base gasket and diffuser |
Did the M38A1 use the metal "V" diffuser as did the L head engines? My 53 M38A1 came with an aftermarket carb, and I am now bring the fuel system back to original with a rebuilt YS carb.
See thi ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
