Author |
Message |
Topic: M38A1 CDN3 wheel cylinders |
jasonm
Replies: 5
Views: 9397
|
Forum: Technical Knowledge Base Posted: Fri Jun 17, 2011 6:50 pm Subject: M38A1 CDN3 wheel cylinders |
Lol Did napa try to tell ya these are american part numbers...lol They tryed that with me.
So i asked him what napa stands for he dident know,North American Auto then you have to remind them we are ... |
Topic: M38A1 CDN3 wheel cylinders |
jasonm
Replies: 5
Views: 9397
|
Forum: Technical Knowledge Base Posted: Wed Jun 15, 2011 6:32 pm Subject: M38A1 CDN3 wheel cylinders |
Just take the number and go to canadian tire , thats all i did they were ordered and i had them in two days,they were around 30.00 each.
You can do it also at napa, but there prices are realy out the ... |
Topic: Help with rounded lug nuts |
jasonm
Replies: 7
Views: 8110
|
Forum: Technical Knowledge Base Posted: Sun May 29, 2011 3:23 pm Subject: Help with rounded lug nuts |
A 10 dollar Nut splitter,Its a tool that slips over a bolt it has a small hardened blade on one side ,you tighten it up untill it cuts off the nut and does not damage the threads, they come in severa ... |
Topic: Rubber brake lines |
jasonm
Replies: 9
Views: 9912
|
Forum: Technical Knowledge Base Posted: Sun May 22, 2011 1:46 pm Subject: Rubber brake lines |
If measuring it is from sealing seat to sealing seat its only 9 1/2.
this could be the problem. |
Topic: Rubber brake lines |
jasonm
Replies: 9
Views: 9912
|
Forum: Technical Knowledge Base Posted: Sun May 22, 2011 11:04 am Subject: Rubber brake lines |
Afternoon Wes, Infact I am doing it the way you say from the back side, I do not have my lines made yet as i always put on the rubber lines first to be sure i have enough steel line.
However I am sti ... |
Topic: Rubber brake lines |
jasonm
Replies: 9
Views: 9912
|
Forum: Technical Knowledge Base Posted: Sun May 22, 2011 8:07 am Subject: Rubber brake lines |
Ok guys I will give that a try,I will also try sitting the axle and tires down on the ground to gain some room, right now i have it supported on jack stands on the frame so every thing is high and dry ... |
Topic: Rubber brake lines |
jasonm
Replies: 9
Views: 9912
|
Forum: Technical Knowledge Base Posted: Sat May 21, 2011 7:24 pm Subject: Rubber brake lines |
Putting rubber brake lines on the m-38 this weekend,and think i may have run into a snag.
The long lines measure 11 inch and 15 inches or is it 15 and 18 inches?
I tryed the 11inch on the front as i ... |
Topic: tie rod ends |
jasonm
Replies: 29
Views: 31350
|
Forum: Technical Knowledge Base Posted: Wed May 11, 2011 2:43 pm Subject: tie rod ends |
Wesk, Thanks, You have answered my question.
Jason |
Topic: tie rod ends |
jasonm
Replies: 29
Views: 31350
|
Forum: Technical Knowledge Base Posted: Mon May 09, 2011 4:57 am Subject: tie rod ends |
Wesk, I am sorry that you take my post as a low blow,For that was not what it was meant as, I was just making point to the measurment offered and how they dont measure up.
I have used your search fun ... |
Topic: tie rod ends |
jasonm
Replies: 29
Views: 31350
|
Forum: Technical Knowledge Base Posted: Sun May 08, 2011 6:32 pm Subject: tie rod ends |
Ah but I didenty say that i had a mix and match, I asked how do you measure and where do you come up with 3/4 or 11/16 because when measured they all are 5/8 thats thin and thick tie rods.
Dont be so ... |
Topic: tie rod ends |
jasonm
Replies: 29
Views: 31350
|
Forum: Technical Knowledge Base Posted: Sun May 08, 2011 8:44 am Subject: tie rod ends |
So I take it know one has replaced the tie rod ends on there jeeps in 50 years...Must be alot of unsafe restored jeeps out there..lol |
Topic: tie rod ends |
jasonm
Replies: 29
Views: 31350
|
Forum: Technical Knowledge Base Posted: Wed May 04, 2011 8:07 pm Subject: tie rod ends |
Ya thats what i thought too, but the measurment is 5/8 and is the same on all tie rods that i have come across, my slat grill and gpw also the m-38 are all the same.
Still confused, but thanks just t ... |
Topic: Brake lines |
jasonm
Replies: 26
Views: 35164
|
Forum: Technical Knowledge Base Posted: Wed May 04, 2011 7:02 pm Subject: Brake lines |
Always double flar on brake lines, because you wont get a second chance! |
Topic: tie rod ends |
jasonm
Replies: 29
Views: 31350
|
Forum: Technical Knowledge Base Posted: Wed May 04, 2011 6:59 pm Subject: tie rod ends |
Guys, I have been thinking about this now for about two days and am now down to about three hairs on my head,How do you measure the tie rod ends?
Some venders are asking wich ones you need 3/4 or 11/ ... |
Topic: M38 Vacuum lines. |
jasonm
Replies: 10
Views: 15039
|
Forum: Wanted Posted: Fri Apr 29, 2011 7:50 pm Subject: M38 Vacuum lines. |
You can buy the boxes of 50 for the S clips at Fastenall or spayner, they are around 20 dollars.
Jason |
|