Author |
Message |
Topic: dash primer pump leaks with inline fuel pump |
sgtkish
Replies: 13
Views: 15514
|
Forum: Technical Knowledge Base Posted: Sun Feb 12, 2017 7:20 pm Subject: dash primer pump leaks with inline fuel pump |
It doesn't get any more squared away of a response then that. Thanks again Wes.
Mark |
Topic: dash primer pump leaks with inline fuel pump |
sgtkish
Replies: 13
Views: 15514
|
Forum: Technical Knowledge Base Posted: Sun Feb 12, 2017 4:36 pm Subject: dash primer pump leaks with inline fuel pump |
Thank you, that's what I'll do. I'll put a shut off valve on there once I figure out the suck line fitting size. That way I can pump it a couple time in the cold before I turn the actual pump on. I wi ... |
Topic: dash primer pump leaks with inline fuel pump |
sgtkish
Replies: 13
Views: 15514
|
Forum: Technical Knowledge Base Posted: Sun Feb 12, 2017 11:49 am Subject: dash primer pump leaks with inline fuel pump |
How's this for a guess, does anyone thing this electric pump is forcing fuel threw the dash primer and I to the manifolds injector ports making the truck run at the high rpms its doing right now?
... |
Topic: dash primer pump leaks with inline fuel pump |
sgtkish
Replies: 13
Views: 15514
|
Forum: Technical Knowledge Base Posted: Sun Feb 12, 2017 8:56 am Subject: dash primer pump leaks with inline fuel pump |
Thanks for the information, that makes since, it would pressurize that primer line. I was thinking of just plugging the line off, but I hate to lose that option. The old pump still works, its just lea ... |
Topic: dash primer pump leaks with inline fuel pump |
sgtkish
Replies: 13
Views: 15514
|
Forum: Technical Knowledge Base Posted: Sat Feb 11, 2017 11:41 pm Subject: dash primer pump leaks with inline fuel pump |
I installed a 24v inline fuel pump on my vehicle and had a couple issues I hope someone can enlighten me on. First off the truck runs much higher in rpms now with the 9 psi pump on it and I don't thin ... |
Topic: Lower gear ratio for axles |
sgtkish
Replies: 5
Views: 7658
|
Forum: Technical Knowledge Base Posted: Tue May 10, 2016 2:26 pm Subject: Lower gear ratio for axles |
Thanks to the correction, I can see why that is. Raising the number just lowers the speed. Well if you want to keep your rpms down to normal of course. The ring and pinion tooth count I mentioned was ... |
Topic: Lower gear ratio for axles |
sgtkish
Replies: 5
Views: 7658
|
Forum: Technical Knowledge Base Posted: Mon May 09, 2016 7:57 pm Subject: Lower gear ratio for axles |
I have been thinking about lowering the gear ratio on the ring and pinion for my 1952 m38a1. I'm not sure what size to go with yet, or if its like the m37 and only has one option. I'm a little on the ... |
Topic: electrical |
sgtkish
Replies: 23
Views: 24985
|
Forum: Technical Knowledge Base Posted: Thu Jan 14, 2016 10:50 pm Subject: electrical |
Sorry to revisit this subject but I'm just about done, and ready to turn over the engine for the first time and ran into some wiring issues. Not only does my brake lights stay on the then go off when ... |
Topic: ignition switch hook up |
sgtkish
Replies: 5
Views: 13828
|
Forum: Technical Knowledge Base Posted: Wed Dec 23, 2015 9:25 pm Subject: ignition switch hook up |
All of this info is available through the search function above,
and the many photo pages. Wes has several photos and diagrams
of the back of the instrument cluster showing wiring, gauges,
circuit ... |
Topic: ignition switch hook up |
sgtkish
Replies: 5
Views: 13828
|
Forum: Technical Knowledge Base Posted: Wed Dec 23, 2015 7:06 pm Subject: Re: ignition switch hook up |
Does anyone have a pic of where wire 27 goes to the dash? All the diagrams don't show in detail where it plugs in at, or if its just a ground you strap to the metal dash. I would like to see how the o ... |
Topic: ignition switch hook up |
sgtkish
Replies: 5
Views: 13828
|
Forum: Technical Knowledge Base Posted: Wed Dec 23, 2015 7:05 pm Subject: ignition switch hook up |
Does anyone have a pic of where wire 27 goes to the dash? All the diagrams don't show in detail where it plugs in at, or if its just a ground you strap to the metal dash. I would like to see how the o ... |
Topic: m38a1 valves not fitting |
sgtkish
Replies: 6
Views: 7640
|
Forum: Technical Knowledge Base Posted: Sat Dec 05, 2015 6:23 pm Subject: m38a1 valves not fitting |
Hello kish,
I moved your post here where it will get a better chance of getting a reply.
The M Series Parts Supply & Service Review is for folks that have a product and want to offer it to ... |
Topic: m38a1 valves not fitting |
sgtkish
Replies: 6
Views: 7640
|
Forum: Technical Knowledge Base Posted: Sat Dec 05, 2015 10:30 am Subject: m38a1 valves not fitting |
Valves m38a1
I can't find any exhaust valves for my f134 ,and I have already bought 2 sets from people that say they should fit. The taper on my old valves are not even close to these new ones I'm ... |
Topic: engine # |
sgtkish
Replies: 4
Views: 5600
|
Forum: Technical Knowledge Base Posted: Sat Dec 05, 2015 12:23 am Subject: engine # |
The R represents a Factory new replacement engine built for the Military for use in the M38A1/M170. The military contracts for the Jeeps included a specified number of spare new replacement engines.
... |
Topic: electrical |
sgtkish
Replies: 23
Views: 24985
|
Forum: Technical Knowledge Base Posted: Sat Nov 28, 2015 5:18 pm Subject: electrical |
As long as the plug is the same 4 pin plug you'll not have any problems if you just follow the photos I posted above. I googled the part number and found 2 dealers selling the cable for about $150 at ... |
|