Author |
Message |
Topic: Transmission Shifter Box Gasket |
vuldub
Replies: 3
Views: 5534
|
Forum: Technical Knowledge Base Posted: Tue Nov 14, 2017 10:13 am Subject: Transmission Shifter Box Gasket |
My new gasket was about match book thickness...a little thicker than paper thin and i used gasket sealer spread thin on the gasket and case when putting the shifter on.
Perfect. Thanks |
Topic: Transmission Shifter Box Gasket |
vuldub
Replies: 3
Views: 5534
|
Forum: Technical Knowledge Base Posted: Tue Nov 14, 2017 9:05 am Subject: Transmission Shifter Box Gasket |
Hello. I am about to make a gasket (642770) for between the shifter column box and the top of the T90 transmission. The previous owner only used RTV so I don't have an old gasket to compare. I live ... |
Topic: Fuel tank vent suggestion |
vuldub
Replies: 16
Views: 21232
|
Forum: Technical Knowledge Base Posted: Thu Apr 13, 2017 10:19 am Subject: Fuel tank vent suggestion |
Thanks WesK. I cannot run the vent line to my carb as its not stock. I would need to install a carbon canister and purge valve, which I don't really want to do. Rather than using the original hard ... |
Topic: Fuel tank vent suggestion |
vuldub
Replies: 16
Views: 21232
|
Forum: Technical Knowledge Base Posted: Wed Apr 12, 2017 12:38 pm Subject: Fuel tank vent suggestion |
http://willysmjeeps.com/v2/modules/gallery/albums/album115/Fig_69_A1_Tank.sized.jpg
Sorry to dredge up an old post, but I would like to know more about this "vent valve". There's no part number. ... |
Topic: Fuel Tank Filler Tube Screen |
vuldub
Replies: 1
Views: 4293
|
Forum: Technical Knowledge Base Posted: Tue Jan 05, 2016 1:28 pm Subject: Fuel Tank Filler Tube Screen |
I'm swapping my fuel tank out for one that I am refurbishing, but the screen on the filler tube is ripped to pieces. Has any one soldered on a new brass screen? |
Topic: Dual Master Upgrade |
vuldub
Replies: 11
Views: 12382
|
Forum: Technical Knowledge Base Posted: Mon Jul 29, 2013 1:39 pm Subject: Dual Master Upgrade |
Great. Thanks guys. Two thumbs up. |
Topic: Battery Box Heater |
vuldub
Replies: 1
Views: 3410
|
Forum: Technical Knowledge Base Posted: Fri Jul 26, 2013 11:28 am Subject: Battery Box Heater |
Has anyone converted the M38 battery box with an aftermarket heater, like the mojave or heater craft?
My m38 has been modified so keeping it original is not in my plans (hope that isn't offensive o ... |
Topic: Dual Master Upgrade |
vuldub
Replies: 11
Views: 12382
|
Forum: Technical Knowledge Base Posted: Wed Jul 24, 2013 11:32 am Subject: Dual Master Upgrade |
Thinking about this more, if I have drums all around and I buy a 72 dual master specific to drums w/o power booster, wouldn't the residual pressure valve already be setup inside for similar pressure ( ... |
Topic: Dual Master Upgrade |
vuldub
Replies: 11
Views: 12382
|
Forum: Technical Knowledge Base Posted: Wed Jul 24, 2013 10:59 am Subject: Dual Master Upgrade |
If you plan on staying with a 72-76 CJ5 brake system it would be a good idea to get a 72-76 CJ5 parts and service manual. The 72 manual shows no proportioning valve. Only two residual check valves, on ... |
Topic: Dual Master Upgrade |
vuldub
Replies: 11
Views: 12382
|
Forum: Technical Knowledge Base Posted: Wed Jul 24, 2013 7:11 am Subject: Dual Master Upgrade |
Thanks Wes. My master cylinder is not floor mounted, it's on the firewall. The pedals on my m38 have been swapped out along with the steering column. Herm's master looks like it will bolt right int ... |
Topic: Dual Master Upgrade |
vuldub
Replies: 11
Views: 12382
|
Forum: Technical Knowledge Base Posted: Tue Jul 23, 2013 1:14 pm Subject: Dual Master Upgrade |
Current setup
11" x 2" shoes, 11" drums all around (front and rear)
Front wheel cylinders 1 1/8" bore
Rear wheel cylinders 15/16" bore
Single reservoir master 1" bore
Firewall mounted master (upg ... |
Topic: Shackle Pivot Bearing |
vuldub
Replies: 4
Views: 5434
|
Forum: Technical Knowledge Base Posted: Mon Jul 15, 2013 7:49 am Subject: Shackle Pivot Bearing |
Press fit. TM9-1804B pg 150, par 138.
Thanks, |
Topic: Shackle Pivot Bearing |
vuldub
Replies: 4
Views: 5434
|
Forum: Technical Knowledge Base Posted: Fri Jul 12, 2013 10:30 am Subject: Shackle Pivot Bearing |
Yes, I have those diagrams.
In this one:
http://willysmjeeps.com/v2/modules.php?set_albumName=album201&id=Front_springs&op=modload&name=gallery&file=index&include=view_photo.php
... |
Topic: Shackle Pivot Bearing |
vuldub
Replies: 4
Views: 5434
|
Forum: Technical Knowledge Base Posted: Fri Jul 12, 2013 7:31 am Subject: Shackle Pivot Bearing |
Is this bearing pressed into the spring? I'm going to replace the spring shackles (two of the grease nipples are missing and threads stripped -won't take an new nipple) and thought it might be worth ... |
Topic: m38 Fuel Sending Unit |
vuldub
Replies: 8
Views: 11764
|
Forum: Technical Knowledge Base Posted: Thu Jul 11, 2013 8:47 am Subject: m38 Fuel Sending Unit |
I assume you are talking about an aftermarket 12V unit for a CJ2A/3A since those two jeeps came stock as 6 volters. The only issue would be drilling the sender lid with holes to match the M38 tank scr ... |
|