Author |
Message |
Topic: saggy a1 |
zeke57
Replies: 3
Views: 3401
|
Forum: Technical Knowledge Base Posted: Sun Sep 13, 2020 7:33 pm Subject: saggy a1 |
After reading Wes's post regarding "jeep lean" I may try shimming the right rear spring as suggested. My question is how thick of a shim do I need to use to correct a 1'' lean, 1 inch? |
Topic: saggy a1 |
zeke57
Replies: 3
Views: 3401
|
Forum: Technical Knowledge Base Posted: Fri Sep 04, 2020 3:07 pm Subject: saggy a1 |
When looking at the front of my a1 sitting in my driveway I noticed the driver side seemed to be sagging. So the first thing I did was check the air pressure in all four tires and make sure they were ... |
Topic: Fuel primer |
zeke57
Replies: 6
Views: 4419
|
Forum: Technical Knowledge Base Posted: Sun Aug 09, 2020 12:04 pm Subject: Fuel primer |
I am not seeing any mention of a primer arm on the carb in any of my manuals. The only primer arm that I am aware of is on the fuel pump. |
Topic: Fuel primer |
zeke57
Replies: 6
Views: 4419
|
Forum: Technical Knowledge Base Posted: Fri Aug 07, 2020 10:21 am Subject: Fuel primer |
I have noticed if my a1 sit's for any period of time it is very hard to start so I have to remove the air cleaner tube and squirt gas into the carb. I have read about solution's to this problem among ... |
Topic: m38a1 pintle |
zeke57
Replies: 5
Views: 5028
|
Forum: Technical Knowledge Base Posted: Sat Jul 11, 2020 6:38 pm Subject: m38a1 pintle |
I want to add a pintle hook to my a1 and was wondering if they are all the same or were there different versions for different years. |
Topic: stencils |
zeke57
Replies: 6
Views: 5468
|
Forum: Technical Knowledge Base Posted: Sat Jun 27, 2020 6:20 pm Subject: stencils |
2nd that. I purchased my stencils from Delta very satisfied with them. |
Topic: M38A1 Tub Craigslist Escondido CA |
zeke57
Replies: 3
Views: 5764
|
Forum: For Sale Posted: Fri Jun 19, 2020 6:13 pm Subject: M38A1 Tub Craigslist Escondido CA |
Looks like a great deal for someone. |
Topic: Coil question |
zeke57
Replies: 6
Views: 5532
|
Forum: Technical Knowledge Base Posted: Mon May 04, 2020 6:49 am Subject: Coil question |
I forgot to mention that I did a 12v conversion sorry about that. I read an old post on this forum from July of 2018 in which Wes mentions that the Prestolite 200691 was the coil used on the f134 for ... |
Topic: Coil question |
zeke57
Replies: 6
Views: 5532
|
Forum: Technical Knowledge Base Posted: Sun May 03, 2020 8:24 pm Subject: Coil question |
Thanks Wes I knew after taking the readings the coil was bad I just wanted to make sure that I did not need a special coil to use with the electronic distributor. So coil shopping I go. Anyone have a ... |
Topic: Coil question |
zeke57
Replies: 6
Views: 5532
|
Forum: Technical Knowledge Base Posted: Sun May 03, 2020 5:06 pm Subject: Coil question |
When using an electronic distributor is it ok just to use a standard coil? I tried to start my a1 last night but it would not fire. I did have it running a few months ago with the same ignition system ... |
Topic: M38a1 Tub Mounting |
zeke57
Replies: 3
Views: 3040
|
Forum: Technical Knowledge Base Posted: Sat Apr 25, 2020 8:55 pm Subject: M38a1 Tub Mounting |
If you go to the "technical knowledge base" page 4 the fourth posting up from the bottom read the "a1 reassembly" post that I authored this may or may not help you out a little. |
Topic: Water pump advice f134 |
zeke57
Replies: 8
Views: 6485
|
Forum: Technical Knowledge Base Posted: Sat Apr 25, 2020 5:34 am Subject: Water pump advice f134 |
Sorry I forgot to mention that I am running a single belt pulley. |
Topic: Water pump advice f134 |
zeke57
Replies: 8
Views: 6485
|
Forum: Technical Knowledge Base Posted: Fri Apr 24, 2020 6:28 pm Subject: Water pump advice f134 |
Thanks everyone for your advice. I ended up ordering a pump from Walcks and it comes with a pulley which I assume is already installed. |
Topic: Water pump advice f134 |
zeke57
Replies: 8
Views: 6485
|
Forum: Technical Knowledge Base Posted: Fri Apr 24, 2020 6:02 am Subject: Water pump advice f134 |
Thank you for the comments Wes. I am not familiar with the term "loading" could you please elaborate. |
Topic: Water pump advice f134 |
zeke57
Replies: 8
Views: 6485
|
Forum: Technical Knowledge Base Posted: Thu Apr 23, 2020 8:19 pm Subject: Water pump advice f134 |
I filled the cooling system yesterday only to find this morning a coolant leak which appears to be coming from the water pump so I guess I will have to replace it. So are all pumps the same in quality ... |
|