Create an account Home  ·  ·  Forums  ·  ·  Articles  ·  ·  Downloads  ·  ·  Photo Gallery  
Login
Nickname

Password

Don't have an account yet? You can create one here.

Navigation
· Home
· Article Archive
· Article Submit
· Downloads
· FAQ
· Forums
· Members List
· Photo Gallery
· Private Messages
· Web Links
· Your Account

Search Articles



Forums

Wiper motor...which is the correct one?
Lead additive, one more question.
M31C mount with or without replica weapon
Backfire and Hesitation
Wanted: Steering column and shaft for M38-1952, or late CJ2A
2024 CT. MILITARY VEHICLE SHOW AND FLEA MARKET- JUNE 15,2024
Brake Line
How to link full size photos in posts
Clutch release bearing support cast tab for return spring
T90 case replacement required?

Willys M Jeeps Forums


willysmjeeps.com :: View topic - M38A1C Issues with high speed
 Forum FAQForum FAQ   SearchSearch   UsergroupsUsergroups   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

M38A1C Issues with high speed

 
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> Technical Knowledge Base
View previous topic :: View next topic  
Author Message
mydadsjeep
Member


Joined: Apr 26, 2017
Posts: 49
Location: Butler pa

PostPosted: Sun Oct 04, 2020 2:02 pm    Post subject: M38A1C Issues with high speed Reply with quote

Ok, Finally got back on the site. I have a 1952 M38A1C and so far the mechanic and I have replace the gas tank, lines, rebuilt the carb the starter and coils and plugs are fine. Only starts to miss at higher speeds around 45 mph. Even going up the hills it slows down and misses still there.
Now I don't know much about the actually specs and how the motor works but he said it maybe that the compression issues and rings since it sat for around 35 years.
https://i.redd.it/w6sy2ifgusi51.jpg
Here is a picture. So any ideas we can try?>
Back to top
View user's profile Send private message Send e-mail
wesk
Site Administrator
Site Administrator


Joined: Apr 04, 2005
Posts: 16225
Location: Wisconsin

PostPosted: Sun Oct 04, 2020 3:47 pm    Post subject: Reply with quote

It may work better if you allow your mechanic to communicate here with us on this site so we might be able to get two mechanics together right here in the topic.

To answer your question which I assume is not from a mechanic?

The best approach to troubleshooting any power problem is to properly test the machines operating parameters with the proper test equipment then follow the already available troubleshooting guide in the M38A1 / C service manual.

This means take test readings where needed and follow the step by step procedures in the troubleshooting manual. TM 9-8014. If you do not have this manual it is available free in PDF format on our downloads page.

It is common to get the following test readings when troubleshooting a high speed power loss.

Compression test
Leakdown test
Timing tests both static and dynamic as well as checking centrifugal advance.
Test Fuel press at carb.
Test Fuel quantity/flow rate delivered.
Test vent system for fuel tank and carb bowl.

Are you still selling that jeep. I have some old photos apparently taken Sep 2013 in my M38A1 FS files.
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail Visit poster's website
mydadsjeep
Member


Joined: Apr 26, 2017
Posts: 49
Location: Butler pa

PostPosted: Sun Oct 04, 2020 4:40 pm    Post subject: jeep Reply with quote

The jeep in the woods is still there. I had offered $1000 for it and he said yes then later backed out/ I had a friend call him months later and same thing, accepted an offer then backed out. Ill see if I can get my mech on here...
Back to top
View user's profile Send private message Send e-mail
wesk
Site Administrator
Site Administrator


Joined: Apr 04, 2005
Posts: 16225
Location: Wisconsin

PostPosted: Sun Oct 04, 2020 7:58 pm    Post subject: Reply with quote

Looks like the jeep in the woods from back then has the same hard top as your current jeep.


The photo you just sent of your A1 now.


The old jeep in the filed photo.

I guess looking at it again the jeep in the field has a different hard top.
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail Visit poster's website
G740
Member


Joined: Jan 27, 2006
Posts: 498

PostPosted: Sun Oct 04, 2020 8:58 pm    Post subject: Engine miss Reply with quote

I get this question a lot at my business. 9 times out of 10, it is the distributor. The most over looked piece when people do restorations or even just a runner is the distributor. To most people, rebuilding it is simply putting points, condenser, cap and rotor. Ah, but there is so much more. Counter weights, springs, bushings, shaft wear, cam wear etc etc.
Grab the rotor and push it to one side. If you can push it to the side and open the points, you have bushing wear and at higher rpm, the points float because the shaft of the distributor no longer runs in a circle, it runs in an ellipse. Once this occurs, the miss starts and does not go away until it goes back to idle.
I rebuild distributors all the time and most all say that their vehicle has never run that good once installed. Something to look at.
John
Back to top
View user's profile Send private message
mydadsjeep
Member


Joined: Apr 26, 2017
Posts: 49
Location: Butler pa

PostPosted: Mon Oct 12, 2020 8:14 pm    Post subject: Reply with quote

Yea the one in the woods don't have the ridges on it if I remember right
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> Technical Knowledge Base All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Powered by phpBB © 2001 phpBB Group
Forums ©

 



PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.