Alternator to Distributor cable - What size spanner wrench?

cabinfever

The insulation on my alternator to alternator distributor cable is shot. I'm going to remove it and try to do a repair using heat shrink tape (unless someone has a better idea).

To remove the cable, the manual says to use a spanner wrench. I have a lot of tools, but not any spanner wrenches. Can someone help me with the size wrench I should buy (I don't want to buy a whole set)? Or, will I be able to turn the couplings with a channel-lock pliers?

Thanks
_________________
Steve Stark - 1955 M38A1 MD #85388

Member - MVPA #35153
Member - Red Bull Historic Military Vehicle Association

4x4M38 · Posted: Tue Mar 08, 2016 12:38 pm Post subject:

Steve,
Any wrench that fits would be better than Channelocks
which will goober up your fittings.
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php

RICKG · Member Joined: Aug 31, 2010 Posts: 1741 Location: SO IDAHO

http://www.ebay.com/itm/KAL-7502-Adjustable-Pin-Spanner-Wrench-3-4-2-/331792960389?hash=item4d4066cb85:g:WcsAAOSwDuJW109s
http://www.ebay.com/itm/Armstrong-adjustable-pin-spanner-wrench-3-4-2-34-351/281956636174?_trksid=p2047675.c100005.m1851&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D1%26asc%3D20131003132420%26meid%3D9042071d76cf408ebae07837d2e3a884%26pid%3D100005%26rk%3D1%26rkt%3D6%26sd%3D331792960389

Look for one of these guys Steve. Most MV vendors have 'em and Flea Bay is full of them. A good adjustable can be had for around 20 bucks.
_________________
keep 'em rollin'
RICKG MC 51986 DOD 01-52, '50 CJ3a

wesk · Posted: Tue Mar 08, 2016 1:19 pm Post subject:

The spanner referenced by original post is not the usual two flat faces wrench.

Here's a couple of links:
http://www.amazon.com/Williams-474-Adjustable-Spanner-Wrench/dp/B002FHNIXW

http://www.amazon.com/OTC-Adjustable-Hook-Spanner-Wrench/dp/B000RHSNQE

http://www.sears.com/es/us/shc/s/t_10153_12605?tName=2-inch-spanner-wrench.html

http://www.armstrongtools.com/wrenches/spanner
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php

RonD2 · Posted: Tue Mar 08, 2016 1:54 pm Post subject:

I've had good luck with these, especially with cast mil-spec connectors:

http://www.aircraftspruce.com/catalog/topages/at508k.php

Might want to soak it with PB Blaster if it hasn't been off in awhile. I've seen lots of cracked shells using channel locks on cast mil-spec connectors, especially when corroded.
_________________
Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51

“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari

cabinfever · Posted: Tue Mar 08, 2016 6:47 pm Post subject:

Thanks for all the responses and warnings to NOT use a channel-lock pliers.

I still have one of my original questions What size spanner wrench do I need to purchase. I have to believe the removal of this cable will be the ONLY need I'll ever have for a spanner wrench, so I might as well just get one.

Based on the links provided, it appears that a 3/4" to 2" adjustable spanner should work. Is that correct?

I suppose I could reach around my A1 heater or crawl under the A1 and measure the diameter of the connector with my caliper to figure out what size I need....but I'm lazy this time of year. Smile

Anyone know off hand what the OD is of the cable connectors?
_________________
Steve Stark - 1955 M38A1 MD #85388

Member - MVPA #35153
Member - Red Bull Historic Military Vehicle Association

wesk · Posted: Tue Mar 08, 2016 7:09 pm Post subject:

Steve, About the only way any of us could guarantee we are telling you the correct size would be for one of us to do exactly what you are unwilling to do! Rolling Eyes

I can make it easier for you. Just take an adjustable crescent wrench out there and slip the jaws over the connector and measure the opening of the jaws!
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php

cabinfever · Posted: Tue Mar 08, 2016 7:13 pm Post subject:

Not to beat a dead horse, but DeBella Parts sells a NOS spanner wrench for $20 bucks. It is described as "Spanner wrench used for removing cable from volt reg & gen" It's the 13th item down the list found at:

http://www.debellajeepparts.com/m38m38a1miscellaneous.htm

I assume this is what I need...right?
_________________
Steve Stark - 1955 M38A1 MD #85388

Member - MVPA #35153
Member - Red Bull Historic Military Vehicle Association

wesk · Posted: Tue Mar 08, 2016 7:54 pm Post subject:

Steve, Sooner or later you'll just have to get up, set your beer down and go out in the garage and measure the connector Wink

_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php

cabinfever · Posted: Tue Mar 08, 2016 8:09 pm Post subject:

LOL! Wes, I had no idea you knew me so well! Very Happy

_________________
Steve Stark - 1955 M38A1 MD #85388

Member - MVPA #35153
Member - Red Bull Historic Military Vehicle Association

4x4M38 · Posted: Tue Mar 08, 2016 9:10 pm Post subject:

Beer? What beer.....
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php

RonD2 · Posted: Tue Mar 08, 2016 9:42 pm Post subject:

I'm pretty sure the slip-joint spanners or cannon plug pliers can also open anything from a pony to a keg........just my 2 cents as I'm still a rookie Shocked

By the way....has anybody seen my front hub socket wrench?
_________________
Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51

“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari

wesk · Posted: Tue Mar 08, 2016 11:28 pm Post subject:

No worries Ron. I found it in the garage!

_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php

cabinfever · Posted: Wed Mar 09, 2016 8:33 am Post subject:

What this forum needs is a "Like" button.
_________________
Steve Stark - 1955 M38A1 MD #85388

Member - MVPA #35153
Member - Red Bull Historic Military Vehicle Association

skyjeep50 · Member Joined: Feb 20, 2007 Posts: 606 Location: Illinois

The connectors to my voltage regulator and generator are hand tight only. Unless you are taking your jeep swimming underwater there is really no need to tighten the connections with a spanner wrench. Once the connector is loose, just a quarter turn or so, you should be able to spin them off by hand unless they are severely corroded and full of gunk. Try a channel lock and see if you can get things moving with a minimum of force. You might be surprised and not have to worry about finding a specialty wrench.
_________________
1951 M38


Create an account	Home · · Forums · · Articles · · Downloads · · Photo Gallery


PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.