View previous topic :: View next topic |
Author |
Message |
alexandrewillys51 Member
Joined: Nov 01, 2012 Posts: 74 Location: BRASIL
|
Posted: Thu Feb 21, 2013 7:04 am Post subject: QUESTION: Oil Pressure Sender Bracket. |
|
|
Hello friends,
I have a question about this piece (PHOTO).
She was attached to the side of the engine block of the m38?
Served as support for what?
All jeeps m38 wore this piece? That was a change made in a date?
Would you like more details on this piece and what she endured.
Thank you all for your attention.
hug
Alexandre BRAZIL
|
|
Back to top |
|
|
idiocrates Member
Joined: Nov 02, 2007 Posts: 437 Location: Seguin, Texas
|
Posted: Thu Feb 21, 2013 7:30 am Post subject: |
|
|
This piece mounted on the passenger's side of the engine block just aft of the carb (on an F-134) and was used to mount the electrical transducer (or oil pressure sending unit) for the electrical oil pressure gauge. _________________ Jim
***********************
'?? - M38A-1 |
|
Back to top |
|
|
alexandrewillys51 Member
Joined: Nov 01, 2012 Posts: 74 Location: BRASIL
|
Posted: Thu Feb 21, 2013 7:39 am Post subject: |
|
|
idiocrates wrote: | This piece mounted on the passenger's side of the engine block just aft of the carb (on an F-134) and was used to mount the electrical transducer (or oil pressure sending unit) for the electrical oil pressure gauge. |
friend,
Thanks for your response.
So in fact this piece was used in the M38-A1.
The M38 did not use this piece?
I am confirming, because I saw a picture of a m38 (believe L134) with this piece installed.
I'll post a picture and you tell me if I'm wrong.
Thanks again for your attention.
|
|
Back to top |
|
|
chrisk Member
Joined: Apr 22, 2012 Posts: 119 Location: the Netherlands
|
Posted: Thu Feb 21, 2013 8:02 am Post subject: |
|
|
That is the support, oil pressure sending unit bracket,assy for the M38A1;
Ordn. Part # 8329686
Mfr's Part # WO-806832
Chris |
|
Back to top |
|
|
idiocrates Member
Joined: Nov 02, 2007 Posts: 437 Location: Seguin, Texas
|
Posted: Thu Feb 21, 2013 8:03 am Post subject: |
|
|
I have very little experience with the M38 or the L-Head 134 engine but I believe the oil pressure sender unit on these units was mounted on the driver's side of the engine very close to where the oil port is immediately in front of the bell housing at the rear of the engine block. _________________ Jim
***********************
'?? - M38A-1 |
|
Back to top |
|
|
alexandrewillys51 Member
Joined: Nov 01, 2012 Posts: 74 Location: BRASIL
|
Posted: Thu Feb 21, 2013 8:07 am Post subject: |
|
|
idiocrates wrote: | I have very little experience with the M38 or the L-Head 134 engine but I believe the oil pressure sender unit on these units was mounted on the driver's side of the engine very close to where the oil port is immediately in front of the bell housing at the rear of the engine block. |
Chris and Jim,
I see, so really this support was not mounted on L-134, the photo I posted, is perhaps an incorrect assembly, where the engines made CJ3A was installed the coil 6v.
I think this photo may be an incorrect installation.
Thanks for your help.
Thank you for taking the time with my doubts.
hugs
Alexandre |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16249 Location: Wisconsin
|
|
Back to top |
|
|
|