| View previous topic :: View next topic |
| Author |
Message |
circleburner12
Member
Joined: May 16, 2011
Posts: 385
Location: arkansas
|
 Posted: Tue Jul 09, 2013 12:26 pm Post subject: hole locations |
 |
|
needing the correct hole mounting location and dimensions for the rear reflector. installed a new rear panel and the needing the info. thxs
_________________
1953 m38a1 1953 m100 |
|
| Back to top |
|
 |
chrisk
Member
Joined: Apr 22, 2012
Posts: 119
Location: the Netherlands
|
| Posted: Thu Jul 11, 2013 5:21 am Post subject: |
|
|
Hi circleburner12,
See my member album "sinrisnekaf"on page 8.
There is an image Dimensions Rear Panel page 2of2, the location of the reflector is outlined in red.
Chris
_________________
2x 1956 M38A1(Nekaf);1954 1/4TON trailer,Polynorm(Dutch);1983 Honda VF750C (Magna) |
|
| Back to top |
|
|
circleburner12
Member
Joined: May 16, 2011
Posts: 385
Location: arkansas
|
| Posted: Thu Jul 11, 2013 11:32 am Post subject: |
|
|
thxs chrisk, unless im missing something, the dimensions you speak of on page 2 is for the jeep. im asking for the reflector mounting holes for the m100. thxs
_________________
1953 m38a1 1953 m100 |
|
| Back to top |
|
|
chrisk
Member
Joined: Apr 22, 2012
Posts: 119
Location: the Netherlands
|
| Posted: Fri Jul 12, 2013 1:48 am Post subject: hole locations |
|
|
Sorry, overlooked that it is a M100 trailer.
Chris
_________________
2x 1956 M38A1(Nekaf);1954 1/4TON trailer,Polynorm(Dutch);1983 Honda VF750C (Magna) |
|
| Back to top |
|
|
circleburner12
Member
Joined: May 16, 2011
Posts: 385
Location: arkansas
|
| Posted: Fri Jul 12, 2013 10:07 am Post subject: |
|
|
thanks anyway.
_________________
1953 m38a1 1953 m100 |
|
| Back to top |
|
|
jeepman
Member
Joined: May 21, 2010
Posts: 16
|
| Posted: Fri Jul 12, 2013 11:39 am Post subject: Hole Location |
|
|
| Circleburner,I just when out and checked my 52 M100 rear panel.It just happens my reflectors are not reinstalled yet,Here are the dimensions I found.These are all measured to the center of the holes.The holes are 4 inches in from the side end of the rear panel,Note this is the end of the panel not the box side.The bottom hole is 2 and 15/16 inches up from the bottom edge of the panel itself not the frame rail.The top hole is 6 and 7/8 inches up from the bottom edge of the panel.Hope this helps.I would drill the bottom holes first then use your reflector to mark the top hole for a good fit. |
|
| Back to top |
|
|
circleburner12
Member
Joined: May 16, 2011
Posts: 385
Location: arkansas
|
| Posted: Fri Jul 12, 2013 6:41 pm Post subject: |
|
|
jeepman thank you. thxs
_________________
1953 m38a1 1953 m100 |
|
| Back to top |
|
|
|
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
