willysmjeeps.com

Posted: **Thu Apr 15, 2021 7:44 pm**

I am still making vent and fuel lines for the M-38 and M-38A1. While doing my own restorations I have come across some parts that are needed for the lines.
First is the 3/16" inverted flare junction elbow used in both jeeps - In the M-38 this fitting is used in the vent line (2 EA) from the air filter to the master cylinder. The M-38A1 uses one in the vent line from the Air Filter to the Fuel Tank vent, the other is used in the vent line from the Air Filter to the Master Cylinder. Source I have found - www.etrailer.com Part Number BH-L-3FIF

Next are two "S" type clips; First is a 1/4" to 1/4" clip used on the 1/4" vacuum pump lines on the M-38 (2 or 3 EA). Next is a 1/4" to 5/16" clip (5 EA) needed on the vent line from the Air Filter to the Elbow on the vent line. These clip the vent line to the fuel line (must have 5 1" loom pieces on the fuel line) to hold the vent line to the frame. Both of these clips are available from inlinetube.com ...
First is Part Number CLP108
Second one is here Part number is INL10931.

I hope this helps with getting your Jeep's up and running with the correct parts...

Posted: **Fri Apr 16, 2021 7:37 pm**

wesk wrote:I am still making vent and fuel lines for the M-38 and M-38A1. While doing my own restorations I have come across some parts that are needed for the lines.
First is the 3/16" inverted flare junction elbow used in both jeeps - In the M-38 this fitting is used in the vent line (2 EA) from the air filter to the master cylinder. The M-38A1 uses one in the vent line from the Air Filter to the Fuel Tank vent, the other is used in the vent line from the Air Filter to the Master Cylinder. Source I have found - www.etrailer.com Part Number BH-L-3FIF

First is the 3/16" inverted flare union elbow used in both jeeps - In the M-38 this fitting is used in the vent line (2 EA) from the air filter to the master cylinder. The M-38A1 uses one in the vent line from the Air Filter to the Fuel Tank vent, the other is used in the vent line from the Air Filter to the Master Cylinder. Source I have found - www.etrailer.com Part Number BH-L-3FIF

Next are two "S" type clips; First is a 1/4" to 1/4" clip used on the 1/4" vacuum pump lines on the M-38 (2 or 3 EA). Next is a 1/4" to 5/16" clip (5 EA) needed on the vent line from the Air Filter to the Elbow on the vent line. These clip the vent line to the fuel line (must have 5 1" loom pieces on the fuel line) to hold the vent line to the frame. Both of these clips are available from inlinetube.com ...
First is Part Number CLP108
Second one is here Part number is INL10931.

I hope this helps with getting your Jeep's up and running with the correct parts...

I have absolutely no idea why, but if we try to post the word "union" on this site, it redirects you to the main page, with no error. It makes no sense. It's not on any censored word list, there's no logical explanation as to why you can't say "union" on this forum.

I guess it's just the forum's way of keeping us from unionizing?

Posted: **Fri Apr 16, 2021 8:17 pm**

union

Posted: **Fri Apr 16, 2021 8:19 pm**

There I just posted the word "union" in my previous post but this time it bounced to the home page.

Posted: **Fri Apr 16, 2021 8:19 pm**

union

Posted: **Fri Apr 16, 2021 8:20 pm**

union

Posted: **Fri Apr 16, 2021 8:51 pm**

Union
So I guess you fixed what ever faulted because of Union??

Posted: **Sat Apr 17, 2021 7:27 am**

You guys are having too much fun with the word!
I think that the GAR veteran's are going crazy right now..... as we fragment....

Posted: **Sun Apr 18, 2021 7:07 am**

Posted: **Wed Apr 21, 2021 10:50 am**

I'm offended,why don't they like us northeners,cause we won the war?

✌

willysmjeeps.com

Hal Miller's Fuel & Vent lines

Hal Miller's Fuel & Vent lines

Re: Hal Miller's Fuel & Vent lines