Page 1 of 2

M-38 / M-38A1 Copper Vent Lines...

Posted: Sat Feb 19, 2011 7:04 am
by OKCM38CDN
M-38 3/16" Copper vent lines with tube nuts and loom assembled and ready to install as per the SNL G-740; consisting of 3 lines:

8676980
TUBE, IGNITOR VENT, assy (9")
8676981
TUBE, IGNITOR VENT TO WIPER, assy (27")
8676982 TUBE, gas tank vent, assy (86")

$25.00 plus $10.00 Shipping USPS Mail

M38A1 3/16" Copper vent lines with tube nuts and loom assembled and ready to install as per the SNL G758; consisting of 8 lines:

8328408
LINE, crankcase to cylinder head, assy (19 3/8 in lg)
8677619
LINE, air cleaner to elbow assy (at dash) (used on vehicles through serial No. 29295) (22 1/2 in. 1g)
8677523
LINE, carburetor ventilator, assy (9 1/16 in. lg)
8673356
LINE, distributor to air cleaner tube, assy (13 in. lg)
8673357
LINE, distributor to vacuum line tee, assy (26 in. lg)
8677028
LINE, elbow to union, assy.(at dash) (used on vehicles through serial No. 29295) (16 1/2 in. lg)
WO-808926
LINE, fuel tank to elbow, assy (at tank) (used on vehicles after serial No. 22336 and through serial No. 23359) (30 3/4 in. lg)
WO-806428
LINE, master cylinder to union, assy (at dash) (used on vehicles through serial No. 29295) (29 in. lg)

$40.00 plus $10.00 shipping USPS Mail

All lines are about an inch longer than needed to allow for adjustments...
Lines will be coiled as needed for shipping.

I accept PayPal (use my email address), Check or MO; Cash at your own risk... email me and I will provide address...

If interested contact me...

Please contact me by clicking on the email button below... please State type of vehicle and Vent Lines in the subject...

Posted: Sat Feb 19, 2011 8:34 pm
by millertime
do you use paypal?

Posted: Sun Feb 20, 2011 7:09 am
by OKCM38CDN
Yes...

Send it to my email address...

Please, send me an email prior so that I can be prepared for your order...

I have 3 orders pending and need to order some more materials... I did not expect this big of a rush...

Thanks...

Posted: Thu Mar 10, 2011 7:01 am
by OKCM38CDN
Bump

$$$$$$

Posted: Sat Mar 12, 2011 8:45 am
by hillbilly21
Money sent ..Thanks again Hal... :D :D :D

Received 2 sets. Nice work. Thank you

Posted: Tue Mar 15, 2011 12:07 am
by ZeroGs
The should be installed during next few months. They look great. Thank you again.

I am glad to know you are back at it.

Posted: Sun Mar 20, 2011 5:29 pm
by OKCM38CDN
Gents, I have edited my posting... I have had to raise the cost of shipping from this point on. All new orders will cost $10 for shipping... Priority Mail has gone up drasticly and so I have made an adjustment...

Sorry for the increase...

lines

Posted: Sun Mar 27, 2011 8:33 am
by hillbilly21
GOT MINE AGAIN THANKS !!!!!!!!!

Posted: Fri Jul 01, 2011 5:39 pm
by OKCM38CDN
Bump

Posted: Sun Jul 03, 2011 7:40 am
by pickle
Hello:

What lines do you still have left? I am interested only in M38 (as per below):

M-38 3/16" Copper vent lines with tube nuts and loom assembled and ready to install as per the SNL G-740; consisting of 3 lines:

8676980
TUBE, IGNITOR VENT, assy (9")
8676981
TUBE, IGNITOR VENT TO WIPER, assy (27")
8676982 TUBE, gas tank vent, assy (86")

are you making them, or are they NOS?

Posted: Sun Jul 03, 2011 1:27 pm
by OKCM38CDN
All vent lines are made to order, so if you want a set let me know the type of vehicle and I make them...


Thanks

Posted: Fri Oct 21, 2011 8:25 am
by whydahdvr
Are you still making the vent lines?
Thanks.

Posted: Fri Oct 21, 2011 7:22 pm
by OKCM38CDN
Yes, just send me an email with what you need...

Posted: Tue Jun 19, 2012 4:04 pm
by OKCM38CDN
Bump

distributor vent lines

Posted: Wed Jun 27, 2012 3:14 pm
by henrydes
Great job and cheaper than I could make them for...Thanks