View previous topic :: View next topic |
Author |
Message |
oilleaker1 Member
Joined: May 14, 2009 Posts: 972 Location: South Dakota
|
Posted: Thu Aug 25, 2011 4:27 pm Post subject: Rear Main Seal Question |
|
|
I'm in the middle of overhaul and I'm confused as to which type rear main seal my '51 MC L head motor should use. Rope?, 5/16 inch wide seal neoprene?, wider seal neoprene?. Do you measure the crank machined surface for width to figure out the type? The engine was previously all messed up by a mechanic that knew nothing about it. I don't want to go by what was in it, cause it's probably wrong. He did alot of things wrong. Too much to go into detail. The motor is definately a early '51 military motor. The well of knowledgw here is what I appreciate, that is why I ask. When I say width: I mean front to back of the crank, not diameter of the crank. My CJ3A or civilian shop manual just shows a seal in the parts break down and that's not enough info. HELP!!!! John |
|
Back to top |
|
|
oilleaker1 Member
Joined: May 14, 2009 Posts: 972 Location: South Dakota
|
Posted: Thu Aug 25, 2011 6:57 pm Post subject: |
|
|
TM 1804 A says rope. It doesn't talk about rolling in the rope with a dowel, or leaving one end short and the other long with a similar arrangement on the other side bridging the gap. It simply says to push it in and cut it off flat with the surface. My motor had the narrow neoprene lip seal. What's the vote out there? |
|
Back to top |
|
|
Oldsalt Member
Joined: Jan 28, 2010 Posts: 179 Location: Texas
|
Posted: Thu Aug 25, 2011 9:13 pm Post subject: |
|
|
I think I'm confused on this. I had thought that all the MC engines used rubber seals because of sealing for the fording system. The TM 1804A that I just downloaded speaks of Rubber packings in paragraph 143. Where did you read about rope?
The advice I've read here many times is to put back the same as you took out. Since you took rubber out, I'd put rubber back in. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16260 Location: Wisconsin
|
Posted: Fri Aug 26, 2011 1:12 am Post subject: |
|
|
Quote: | The TM 1804A that I just downloaded speaks of Rubber packings in paragraph 143. Where did you read about rope?
|
John just confused the two vertical round rope like seals for the two sides of the rear main cap with the early rope seals used around the crank journal. TM 9-1804A only covers the late lip type seal which uses the same two main cap side seals that the earlier rope type seal engines used.
Here's the long and the short of it all.
WWII and early post war CJ's used a rope seal.
The MC and MD blocks used the lip type two piece seal.
In the 1990's the Victor Lip type seals were improperly sized and had a high failure rate. Avoid buying old NOS surplus seals. Seals in current issue victor and Felpro kits are fine.
A pitted or otherwise damaged sealing area on any of the cranks will result in either type seal leaking. Machine shops often overlook cleaning up and polishing this seal area
The same crank fits all the gear drive cam 134's. But the early manufactured cranks used in the rope type seal blocks did not have the dimension of the sealing area kept to a close enough tolerance to work with a lip type seal if that crank showed up in a later lip type seal block. Since you have no way of knowing where your crank originated from, you must check this dimension to be sure the crank you have can be used with a lip type seal. This strict crank sealing surface diameter tolerance is 2.302-2.312". Smaller and the lip seal will not have enough tension on the surface. Larger and the lip seal will be too tight and will fail from heat build up.
The bulletin below makes this quite clear:
This sealing surface is pitted and unusable.
Here's a properly finished sealing surface.
Here's the crank & seal dimensions we are talking about.
Here's the cap dimensions. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
RHarris Member
Joined: Nov 23, 2009 Posts: 40
|
Posted: Fri Aug 26, 2011 4:49 am Post subject: rope rear seal |
|
|
I could not find anything but the rope type seal from Fel-pro around here. I used this in a 53 model and no leaks yet. Robert |
|
Back to top |
|
|
artificer Member
Joined: Feb 16, 2007 Posts: 206 Location: Gold Coast Australia
|
Posted: Fri Aug 26, 2011 5:12 am Post subject: |
|
|
I would be careful using any neoprene seal which straddles the groove & hangs in toward the flywheel....these have been troublesome & cost folk heaps of $$$.
There are narrower LIP neoprene seals which fit only in the seal groove & these are good.
The rope type seals are fine but will not last so long & they MUST be rolled into place then trimmed carefully to dimension WITH a little crush.
IF IT FEELS TOO TIGHT TO TURN THE CRANK, IT IS TOO TIGHT. _________________ John GIBBINS
ASE Master Medium/Heavy Truck & Auto Technician 2002 USA
Licensed Motor Mechanic NSW # MVIC 49593 Current
YOU CAN'T TROUBLESHOOT WHAT YOU DON'T UNDERSTAND |
|
Back to top |
|
|
oilleaker1 Member
Joined: May 14, 2009 Posts: 972 Location: South Dakota
|
Posted: Fri Aug 26, 2011 6:23 am Post subject: |
|
|
I saved my narrow lip neoprene seal and I'm copying this to take to the machine shop. The Felpro kit only had the rope seal in it, so the shop owner ordered a neoprene seal------20.00 each. I think my seal surface needs to be polished cause it looked worn and grooved. Thanks for saving me again! Wes, excellent !!! You get 20 points credit at the next show now, so your lug nuts will pass! This really helps, if any of you guys are doing yours, copy this and take it to your machineist!!!! John |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16260 Location: Wisconsin
|
|
Back to top |
|
|
oilleaker1 Member
Joined: May 14, 2009 Posts: 972 Location: South Dakota
|
Posted: Fri Aug 26, 2011 4:28 pm Post subject: |
|
|
Well, the crank seal area is polished nice, but the lip seal was the fat one with the extended lip. Does anyone know who has the narrow ones??????It may be rope time for me. John |
|
Back to top |
|
|
artificer Member
Joined: Feb 16, 2007 Posts: 206 Location: Gold Coast Australia
|
Posted: Sun Aug 28, 2011 4:09 pm Post subject: |
|
|
Pic courtesy of J Barton's tutorial G503
There are 3 seals shown above....my experience & that of many others is the top one [also shown below]
1st which is a Victor which is a full "WIPER" seal is no good....in my case three seals were damaged when received new, with the flashing bad.
Also if fitted up the Victor will generally be too tight on the crank causing eventual seizure of the rear main bearing. There are numerous example in the Jeep community.
Wipers contact a large area of the crank & when too tight cause copious amounts of frictional heat.
2nd is a thin narrow neoprene 'LIP" seal & I would recommend, if obtainable. It has very little contact or drag on the crank & the crank must be clean.
3rd is the rope type woven "WIPER" seal & there are 2 types only the thin narrow style [as shown in Barton's pic] which fits & slides into the groove is acceptable.
@ the end of the day it is all about feel & knowledge....the shaft when all fitted up must feel & turn very smoothly with acceptable drag. Like I said earlier if it feels too tight it is too tight _________________ John GIBBINS
ASE Master Medium/Heavy Truck & Auto Technician 2002 USA
Licensed Motor Mechanic NSW # MVIC 49593 Current
YOU CAN'T TROUBLESHOOT WHAT YOU DON'T UNDERSTAND |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16260 Location: Wisconsin
|
|
Back to top |
|
|
|