View previous topic :: View next topic |
Author |
Message |
RonD2 Member
Joined: Oct 02, 2014 Posts: 1919 Location: South Carolina, Dorchester County
|
Posted: Thu Mar 24, 2016 5:07 pm Post subject: |
|
|
And thank you Wes. I'm not alone in appreciating what you do here. It must be like herding cats....... _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1919 Location: South Carolina, Dorchester County
|
Posted: Thu Mar 24, 2016 9:31 pm Post subject: |
|
|
Brian,
Appreciate that! Wes very cordially let us off the short end of the plank. I was just <badly> trying to add that it seems to me that with all the clear schematics available to us on these M38 jeeps and the vehicle being so versatile --- that basic electricity rules like Ohms Law (the relationship of volts, amps, resistance, and watts) might help better understand how things work. That, and a multi-meter, helps me anyway. I learned a long time ago that guessing or experimenting with electricity usually doesn't end well. Obey the Law, or else......
Lately I find myself thinking it'd be cheaper in the long run if I could just pay travel and per diem for a "tech assist visit" from guys like Wes or G740, or many others in this forum <including you> to come to SC for a week or so to jerk the knots out of my 1st ever jeep rookie rope....... there I go again......that's a topic for a different forum..... _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
DC Member
Joined: Mar 23, 2016 Posts: 14
|
Posted: Fri Mar 25, 2016 7:52 am Post subject: Thanks for the post |
|
|
Thanks for the post. I have been asking these questions of myself, am a rookie as well, so glad I joined up and can follow. Please post your final outcome. I have an M38a1 that was converted to 12v, and can't afford to bring it fully back, so will stick with the conversion. My gauges are also 24v, so the same delima. I did test the light switch with 12v on the bench, and it works fine. I put together a 12 v power supply so I can test before I ruin the wiring. Anyway, thanks. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
Posted: Fri Mar 25, 2016 8:21 am Post subject: |
|
|
DC, Keep in mind that the built in circuit breaker in your light switch will not give your light system the same protection it enjoyed under 24 volts. With 12 volts and the wattage/resistance of the 12 volt lamps you have changed the load a great deal. Plan on adding circuit protection in the form of separate fuses or circuit breakers for the various lighting circuits or at least a new properly rated fuse or circuit breaker in wire # 15.
The military went to 24V for several reasons. It meant lighter electric motors and wires. But it also meant increased voltage (read pressure here) to make things turn faster). This was bound to be the case just like the upgrade from 6 to 12 V over the early years. Trouble is as voltage goes up load or amperage/current flow is reduced. Now when you take this backwards and reduce voltage to 12 V then you are increasing the load or amperage/current flow which then requires heavier wires and higher amp rated fuses and circuit breakers. If you are using the military harness then you are in luck a bit as the Army used a much heavier gauge wire then needed. But with circuit protection devices you will have to calculate the new current draw / amperage/ load and select the correct size fuse. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Last edited by wesk on Fri Mar 25, 2016 8:27 am; edited 1 time in total |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
DC Member
Joined: Mar 23, 2016 Posts: 14
|
Posted: Fri Mar 25, 2016 5:43 pm Post subject: Thanks |
|
|
Thanks both of you for your reply, I can see this site will be extremely helpful in my project. Wes, I planned on installing a modern fuse box and running my circuits through that. The old harness has been farmerized much, and will need to be upgraded anyway. Also, thanks for using water terms as well. "Pressure". I have always thought of electricity as water flow, makes it much simpler for a fre fighter like me to understand. Like I say, wish I could afford to go back to 24v, but out of my budget at this point. If I find some solutions on gauges since that was the original post, I'll try to post that as well. |
|
Back to top |
|
|
southpw Member
Joined: Jun 15, 2014 Posts: 268 Location: Cambridge, Ontario, Canada
|
Posted: Tue Mar 29, 2016 3:15 pm Post subject: |
|
|
This is the combo Ijust bought. VDO 301-015k
hoping it does the job.
_________________ 1952 M38 project
Brad |
|
Back to top |
|
|
DC Member
Joined: Mar 23, 2016 Posts: 14
|
Posted: Tue Apr 05, 2016 11:12 pm Post subject: What about a 24v step-up on the fuel gauge |
|
|
Thought this could be a KIS option for the original fuel gauge question. I have found a step-up converter that will convert 12v to 24v, usually in various amp ranges. If you know the amperage input for the fuel gauge, then a step-up converter could conceivably give you the 24v you need to run the gauge. I think I saw a 2 amp converter for around $10, and a 10 amp for around $15.
If someone measures that amperage coming to the gauge with 24 volts, that would be good to know. |
|
Back to top |
|
|
85jeepcj Member
Joined: Mar 27, 2016 Posts: 16
|
Posted: Thu Apr 07, 2016 3:38 pm Post subject: |
|
|
Keep in mind that your gas gauge is actually a voltmeter. When 24 volts are applied to a stock 24 volt gauge the meter will read full.
As the fuel level lowers the sender increases resistance, the voltage is decreased causing the gauge reading to drop.
You will not be able to make the stock 24 volt gauge work correctly unless you apply 24 volts,
No tank sender resister will make it work. You would need a stepup power supply, 12v-24
When the tank is full of gas the resistance would be zero. When the tank is empty you would see the highest resistance. |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
|