Create an account Home  ·  ·  Forums  ·  ·  Articles  ·  ·  Downloads  ·  ·  Photo Gallery  
Login
Nickname

Password

Don't have an account yet? You can create one here.

Navigation
· Home
· Article Archive
· Article Submit
· Downloads
· FAQ
· Forums
· Members List
· Photo Gallery
· Private Messages
· Web Links
· Your Account

Search Articles



Forums

RCEME Convoy Lamp
M38 Fuel Señor and fuel gauges (2)
WTB: C-375/VRC Interphone Control Box
wrong pic shown in radio installation manual pages?
WTB: four regulator shock mounts
Willys front seat back cover
A new one from overseas
NOS parts package date
AN/GRC-7 antenna question
Gold Medal award at MVPA Nationals

Willys M Jeeps Forums


willysmjeeps.com :: View topic - Broken Omix Steering Sector Shafts Warning! for my Friends!!
 Forum FAQForum FAQ   SearchSearch   UsergroupsUsergroups   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Broken Omix Steering Sector Shafts Warning! for my Friends!!
Goto page 1, 2, 3  Next
 
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> M Series Parts Supply & Service Review
View previous topic :: View next topic  
Author Message
oilleaker1
Member


Joined: May 14, 2009
Posts: 972
Location: South Dakota

PostPosted: Tue Sep 27, 2016 10:26 am    Post subject: Broken Omix Steering Sector Shafts Warning! for my Friends!! Reply with quote

I figured this was a technical warning. Members of our Jeep groups have experienced a failure you need to immediately know about. Two known steering sector failures have recently occured. The sector shaft is breaking free of the end where the two posts ride in the worm gear. You have no control of your front wheels. This could be fatal!!!!! The culprits are sectors made by Omix Ada. These were 7/8 shafts, and I know the military type was larger. But-------someone could have fit a civilian type Ross box. RICKG will post the photos for you. I hope none of you have this happen to you. Check yours to be sure. Oilly

Quote:
Edited by Wes K :
Both 7/8' and 15/16" shafts are effected by the recall. This is directly from the recall announcement by Omix-Ada: " If you have replaced an Omix steering sector shaft, part numbers 18027.01 (7/8” shaft), 18027.03 (a repair kit with bushings and 7/8” shaft) and 18027.02 (15/16” shaft) identified in this campaign." so be careful and do not assume since you have a 15/16" shaft you are good to go!
Back to top
View user's profile Send private message
RICKG
Member


Joined: Aug 31, 2010
Posts: 1744
Location: SO IDAHO

PostPosted: Tue Sep 27, 2016 11:01 am    Post subject: Reply with quote

Our 2A friend's sector broke while backing into his garage after running errands in Omaha traffic.
Last week our 3A friend's sector broke while coming down off of Tin Cup Pass and we had to lash the steering and tow him down off the mountain.
Both friends were with Oilly and I last week so we were able to photograph 2 identical repops with 2 identical failures.


_________________
keep 'em rollin'
RICKG MC 51986 DOD 01-52, '50 CJ3a
Back to top
View user's profile Send private message Send e-mail
4x4M38
Member


Joined: May 30, 2014
Posts: 3459
Location: Texas Hill Country

PostPosted: Tue Sep 27, 2016 7:47 pm    Post subject: Reply with quote

Thanks for posting guys.

This is NHTSA recall type stuff. From the looks of them those breaks are symptomatic of a manufacturing problem.

Omix Ada needs to be made aware, as well as our vendors selling them.

No one wants any one hurt and no one wants to sell faulty parts.
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail
4x4M38
Member


Joined: May 30, 2014
Posts: 3459
Location: Texas Hill Country

PostPosted: Tue Sep 27, 2016 7:59 pm    Post subject: Reply with quote

Can you ask them when they bought their sector shafts?
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail
oilleaker1
Member


Joined: May 14, 2009
Posts: 972
Location: South Dakota

PostPosted: Wed Sep 28, 2016 5:01 am    Post subject: Reply with quote

Brian, Rick Cline called his supplier. All they said was they would replace it for no cost. We too asked the same questions. Why wouldn't a parts house stop selling them, and try and warn the customers who bought one? If you look closly at Omix Ada shafts on ebay right now, they are not welded and radiused and the crack is visable where the shaft meets the hole through the plate. Crack meaning the machined non-welded joint. It must flex at this point and with a good turn against it, or jarring action, shears the shaft. This is a accident waiting to happen. Yesterday, my brother-in-law looked at his 50 CJ3A and he has one!!!!!!! He called another supplier and that one said: "I don't sell that crap". I would think the suppliers when called would shake in their boots over this. A easy slam dunk for a lawyer. I'm not sure Omix Ada being "off shore" would be easily litigated against. Anyway, we decided to warn our friends! Oilly
Back to top
View user's profile Send private message
Hawkshadow
Member


Joined: Oct 10, 2012
Posts: 310
Location: Toronto, Ontario, Canada

PostPosted: Wed Sep 28, 2016 5:50 am    Post subject: Reply with quote

Very concerned about this! The new sector shaft in mine is omix. Rebuilt only 2 years ago. Has this information been sent to omix?

I looked closely at this picture taken during the rebuild to see if there's a joint visible at the bottom of the shaft. It's not perfectly clear but there may be…

_________________
Jordan

M38 CDN
52-30718
Back to top
View user's profile Send private message
oilleaker1
Member


Joined: May 14, 2009
Posts: 972
Location: South Dakota

PostPosted: Wed Sep 28, 2016 7:38 am    Post subject: Reply with quote

I don't see the "crack" or slit on the inside. Is that the larger 15/16 shaft sector? Notice on the picture of the broken shafts the "crack" or slit before the shattered part. That may help you ID the bad ones. Russ on the CJ2A page has opened a "ticket" with Omix. Hopefully they will weigh in on this problem for us. John
Back to top
View user's profile Send private message
RICKG
Member


Joined: Aug 31, 2010
Posts: 1744
Location: SO IDAHO

PostPosted: Wed Sep 28, 2016 9:54 am    Post subject: Reply with quote

OEM OR CORRECT REPOP BELOW


FAULTY OMIX BELOW

_________________
keep 'em rollin'
RICKG MC 51986 DOD 01-52, '50 CJ3a
Back to top
View user's profile Send private message Send e-mail
oilleaker1
Member


Joined: May 14, 2009
Posts: 972
Location: South Dakota

PostPosted: Thu Sep 29, 2016 5:19 am    Post subject: Reply with quote

The bad sectors had the shaft inserted through the end plate and then welded on the outside. These shafts need to be removed. Originals were forged and then machined or ground to spec all one piece. The Omix shafts were reduced in size where they fit through. So, they are even undersized for the job. Tell all your Jeeper friends that may not see this. John
Back to top
View user's profile Send private message
oilleaker1
Member


Joined: May 14, 2009
Posts: 972
Location: South Dakota

PostPosted: Thu Sep 29, 2016 1:02 pm    Post subject: Reply with quote

If you find yours to have WAT and a hardened button in it for the adjuster, that one is also good. See photos at G 503 in the MB/GPW technical section. I was able to pull my cover with the fender still on and take a look this AM. Well worth your time. John
Back to top
View user's profile Send private message
RICKG
Member


Joined: Aug 31, 2010
Posts: 1744
Location: SO IDAHO

PostPosted: Thu Sep 29, 2016 1:39 pm    Post subject: Reply with quote


_________________
keep 'em rollin'
RICKG MC 51986 DOD 01-52, '50 CJ3a
Back to top
View user's profile Send private message Send e-mail
4x4M38
Member


Joined: May 30, 2014
Posts: 3459
Location: Texas Hill Country

PostPosted: Thu Sep 29, 2016 3:43 pm    Post subject: Reply with quote

That doesn't look like a one piece forging Rick.
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail
wesk
Site Administrator
Site Administrator


Joined: Apr 04, 2005
Posts: 16358
Location: Wisconsin

PostPosted: Thu Sep 29, 2016 8:29 pm    Post subject: Reply with quote

Look closer Brian. The shaft is one piece with the large flange. The large flange is drilled thru in 2 places for the tracking pins. Then it has a shallow well drilled in the face of the flange for the hardened steel pressure button which the adjusting screw bears against.
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail Visit poster's website
oilleaker1
Member


Joined: May 14, 2009
Posts: 972
Location: South Dakota

PostPosted: Fri Sep 30, 2016 6:22 am    Post subject: Reply with quote

Don't forget that the previous owner of your Jeep may have installed one in yours!!!!!!!!!!!! Shocked
Back to top
View user's profile Send private message
Derstrom
Member


Joined: May 23, 2016
Posts: 37

PostPosted: Fri Sep 30, 2016 8:48 am    Post subject: Reply with quote

This kind of thing scares the s*** out of me. That's an unacceptable failure. I will be taking a very skeptical look at any Omix parts in the future. Thanks for posting this y'all.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> M Series Parts Supply & Service Review All times are GMT - 6 Hours
Goto page 1, 2, 3  Next
Page 1 of 3

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Powered by phpBB © 2001 phpBB Group
Forums ©

 



PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.