View previous topic :: View next topic |
Author |
Message |
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
Posted: Sun Feb 09, 2020 5:43 pm Post subject: |
|
|
Hey Ron, the bell housing, tranny and transfer are now pressurized now with the late version.
That hole is for the late version vacuum line system T-Brass at bell housing, 143481. The late system runs a line across the transfer to the tee, then forward to the fuel pump. The tranny and transfer are internally connected.
Have a look at page 72 in Ryan’s book or Harold’s fording ventilation pages under the CJV35 downloads pages.
You are gonna need that neat decal now regarding the drain plug being stowed in the glove box!!
If you find a cheap supply of those brackets let me know.
Bz _________________ Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Sun Feb 09, 2020 6:49 pm Post subject: |
|
|
Thank Brian. Will do. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
ocwd Member
Joined: May 14, 2007 Posts: 721 Location: Placentia, CA
|
Posted: Mon Feb 10, 2020 9:13 am Post subject: 129-Tooth Flywheel |
|
|
I probably have a 129-tooth flywheel. You can have it if you want. You just have to pay shipping from California. It's a very heavy boat anchor. Let me know and i'll pull it out of the shed and check the teeth for you.
Dave |
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Mon Feb 10, 2020 11:54 am Post subject: |
|
|
Hi Dave,
Thanks for the offer! I bit the bullet a couple of days ago and have one inbound from Texas. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Sat Feb 15, 2020 11:39 pm Post subject: |
|
|
NOS 129 tooth flywheel kit. It never ceases to amaze me opening a box containing NOS parts that were probably made more than 50 years ago. Thanks to Brent @ BMJP !
_________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Sun Feb 16, 2020 12:09 am Post subject: |
|
|
I used my last quart of diesel cleaning the cosmoline off the NOS rear engine plate today. Have to get more. Will post a photo later! _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Tue Mar 17, 2020 11:05 am Post subject: |
|
|
Flywheel unpacked and cleaned up ready for trip to machine shop for drilling for straight dowel bolts and balancing with crankshaft and pressure plate. Need to remember and take photo how he marks them for orientation.
_________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Tue Mar 17, 2020 11:18 am Post subject: |
|
|
So far, this little flywheel conversion exercise (with postage) has entailed
---NOS 129-tooth flywheel $160
---Take-off late bell housing $60
---NOS clutch inspection cover and gasket $30
---NOS rear engine plate $40
---NOS engine plate brackets (3) $45
---Take-off set of bell housing mounting bolts (incl 2 NOS dowel bolts) $25
---Working take-off MDM-6005 starter $60
---NOS Filko SD-32 starter drive $40
Kind of reminds me of starting a remodel on the bathroom and ending up in the kitchen..... _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
Posted: Tue Mar 17, 2020 11:48 am Post subject: |
|
|
Quote: | Need to remember and take photo how he marks them for orientation. |
The easiest method is to after you have checked the engine TDC #1 on compression and the the correct timing mark is in the timing window or aligned on the front crank pulley then pull the old flywheel and have them index the dowel bolt holes to match old flywheel. That is if you have the original flywheel or if the original flywheel aligned correctly on your test before teardown or if you even checked the original flywheel for proper timing mark alignment before you tore it down. Most flywheels I have purchased either already had tapered or straight dowel holes drilled and timing marks on the flywheel already. I don't recall ever getting a flywheel with no dowel holes drilled (all 6 holes exactly the same) or no timing marks in place. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Tue Mar 17, 2020 1:29 pm Post subject: |
|
|
Thanks Wes, I appreciate the advice but what started this mess was a bad flywheel, see photos and your comments at top of post. After the decision to switch over from early 97-tooth with tapered dowel bolt holes to the correct 129-tooth, and with an already disassembled engine, I could see no reason to look back at it for any reason other than making a shop stool out of it.
This NOS flywheel out of the box has 4 properly sized bolt holes and 2 larger holes (see photo) that right now won't accept the 1/2-20 straight dowel bolts until the flywheel gets mated to the crankshaft flange at the machine shop and he drills them together at the same time. At least that's the way I read the manual.
Once the machinist mates them together, and then balances them together, I figured it would be no sweat for him to stamp orienting marks on both the crankshaft flange and flywheel for future reference during assembly. I bet he does it without asking anyway, he's that good. I just need to remember to ask to see the marks and photo them.
I see no timing marks on this NOS flywheel and it doesn't surprise me. Why bother marking it before installing it? It can be properly installed one of two ways (180-degrees apart), and that only matters once it's balanced and mated to the crank then installed in the motor. After he marks it, I believe these marks will serve only to mate them as balanced, and have nothing at all to do with timing --- which will now be done at the front of the motor with the timing pointer, assuming I can assemble the rest of the motor correctly.
Am I off base? I believe you taught me well. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 1917 Location: South Carolina, Dorchester County
|
Posted: Tue Mar 17, 2020 5:47 pm Post subject: |
|
|
The rear end. On the 97-tooth flywheel, visible through the timing hole cover on the early rear engine plate that was bolted to the early bell housing.
None of which are currently assembled to the motor, and all of which are of no further use to me after I assemble the motor with the new components.
I figure to try and sell the bell housing and rear engine plate cheap to somebody who can use them for a CJ2A. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
|